Untersucht wurde der Einfluss der Wassersättigung auf die statische und dynamische Druckfestigkeit von Beton. Hierzu wurden zwei verschiedene Probengeometrien mit definierten Sättigungsgraden getestet. Für die dynamischen Druckfestigkeitsversuche wurde der Split‐Hopkinson‐Bar verwendet. Es wurde festgestellt, dass die Druckfestigkeit von Beton mit steigendem Sättigungsgrad abnimmt, sowohl im statischen als auch im dynamischen Belastungsfall. Der Betrag der Abminderung der Druckfestigkeit mit steigender Sättigung ist im statischen und dynamischen Fall gleich. So kann festgehalten werden, dass der Einfluss der Wassersättigung unabhängig von der Dehn‐ und Belastungsgeschwindigkeit ist. Die trockenen Proben versagten explosionsartiger mit einer erhöhten Riss‐ und Bruchstückanzahl im Vergleich zu den wassergesättigten Probekörpern.
The ductile behavior of strain-hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions in applications where high energy dissipation is needed, such as in earthquakes, impacts by projectiles, or blasts. However, the superior tensile ductility of SHCC due to multiple cracking does not necessarily point to compressive and shear ductility. As an effort to characterize the behavior of SHCC under impact compressive and shear loading relevant to the aforementioned high-speed loading scenarios, the paper at hand studies the performance of a particular SHCC and its constituent, cement-based matrices using the split-Hopkinson bar method. For compression experiments, cylindrical specimens with a length-to-diameter ratio (l/d) of 1.6 were used. The selected length of the sample led to similar failure modes under quasi-static and impact loading conditions, necessary to a reliable comparison of the observed compressive strengths. The impact experiments were performed in a split-Hopkinson pressure bar (SHPB) at a strain rate that reached 110 s−1 at the moment of failure. For shear experiments, a special adapter was developed for a split-Hopkinson tension bar (SHTB). The adapter enabled impact shear experiments to be performed on planar specimens using the tensile wave generated in the SHTB. Results showed dynamic increase factors (DIF) of 2.3 and 2.0 for compressive and shear strength of SHCC, respectively. As compared to the non-reinforced constituent matrix, the absolute value of the compressive strength was lower for the SHCC. Contrarily, under shear loading, the SHCC demonstrated higher shear strength than the non-reinforced matrix.
An analytical model is presented in this paper which, based on the maximum crack velocity, provides a hypothesis for one of the reasons of the increase in tensile strength of concrete under high loading rates. Due to the fact that the formation of cracks needs a certain time to pass through the cross section and not happens suddenly, stresses can still be transmitted over the remaining uncracked cross section during this time. The hypothesis is that at high loading rates, the increase in externally induced stresses can be greater than the decrease in the load-bearing cross-sectional area due to limited crack propagation velocity, which results in an externally measurable increase in strength. This measured strength increase depends on the stress distribution in the crack plane. In this paper two variants of this stress distribution during the failure process are described, and their effect on the increase in strength is mathematically evaluated.
The determination of crack propagation velocities can provide valuable information for a better understanding of damage processes of concrete. The spatio-temporal analysis of crack patterns developing at a speed of several hundred meters per second is a rather challenging task. In the paper, a photogrammetric procedure for the determination of crack propagation velocities in concrete specimens using high-speed camera image sequences is presented. A cascaded image sequence processing which starts with the computation of displacement vector fields for a dense pattern of points on the specimen’s surface between consecutive time steps of the image sequence chain has been developed. These surface points are triangulated into a mesh, and as representations of cracks, discontinuities in the displacement vector fields are found by a deformation analysis applied to all triangles of the mesh. Connected components of the deformed triangles are computed using region-growing techniques. Then, the crack tips are determined using the principal component analysis. The tips are tracked in the image sequence and the velocities between the time stamps of the images are derived. A major advantage of this method as compared to the established techniques is in the fact that it allows spatio-temporally resolved, full-field measurements rather than point-wise measurements. Furthermore, information on the crack width can be obtained simultaneously. To validate the experimentation, the authors processed image sequences of tests on four compact-tension specimens performed on a split-Hopkinson tension bar. The images were taken by a high-speed camera at a frame rate of 160,000 images per second. By applying the developed image sequence processing procedure to these datasets, crack propagation velocities of about 800 m/s were determined with a precision in the order of 50 m/s.
The determination of crack propagation velocities can provide valuable information for a better understanding of damage processes of concrete. The spatio-temporal analysis of crack patterns developing at a speed of several hundred meters per second is a rather challenging task. In the paper, a photogrammetric procedure for the determination of crack propagation velocities in concrete specimens using high-speed camera image sequences is presented. A cascaded image sequence processing which starts with the computation of displacement vector fields for a dense pattern of points on the specimen’s surface between consecutive time steps of the image sequence chain has been developed. These surface points are triangulated into a mesh, and as representations of cracks, discontinuities in the displacement vector fields are found by a deformation analysis applied to all triangles of the mesh. Connected components of the deformed triangles are computed using region-growing techniques. Then, the crack tips are determined using principal component analysis. The tips are tracked in the image sequence and the velocities between the time stamps of the images are derived. A major advantage of this method as compared to established techniques is in the fact of its allowing for spatio-temporally resolved, full-field measurements rather than point-wise measurements and that information on crack width can be obtained simultaneously. To validate the experimentation, the authors processed image sequences of tests on four compact-tension specimens performed on a split-Hopkinson tension bar. The images were taken by a high-speed camera at a frame rate of 160,000 images per second. By applying to these datasets the image sequence processing procedure as developed, crack propagation velocities of about 800 m/s were determined with a precision in the order of 50 m/s.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.