Despite the industrial importance of copper oxides, the nature of the (100) surface of Cu 2 O has remained poorly understood. The surface has previously been subject to several theoretical and experimental studies, but has until now not been investigated by atomically resolved microscopy or high-resolution photoelectron spectroscopy. Here we determine the atomic structure and electronic properties of Cu 2 O(100) by a combination of multiple experimental techniques and simulations within the framework of density functional theory (DFT). Low-energy electron diffraction (LEED) and scanning tunneling microscopy (STM) characterized the three ordered surface structures found. From DFT calculations, the structures are found to be energetically ordered as (3,0;1,1), c(2 × 2), and (1 × 1) under ultrahigh vacuum conditions. Increased oxygen pressures induce the formation of an oxygen terminated (1 × 1) surface structure. The most common termination of Cu 2 O(100) has previously been described by a (3√2 × √2)R45°unit cell exhibiting a LEED pattern with several missing spots. Through atomically resolved STM, we show that this structure instead is described by the matrix (3,0;1,1). Both simulated STM images and calculated photoemission core level shifts compare favorably with the experimental results.
An attractive solution to mitigate tars and also to decompose lighter hydrocarbons in biomass gasification is secondary catalytic reforming, converting hydrocarbons to useful permanent gases. Albeit that it has been in use for a long time in fossil feedstock catalytic steam reforming, understanding of the catalytic processes is still limited. Naphthalene is typically present in the biomass gasification gas and to further understand the elementary steps of naphthalene transformation, we investigated the temperature dependent naphthalene adsorption, dehydrogenation and passivation on Ni(111). TPD (temperature-programmed desorption) and STM (scanning tunneling microscopy) in ultrahigh vacuum environment from 110 K up to 780 K, combined with DFT (density functional theory) were used in the study. Room temperature adsorption results in a flat naphthalene monolayer. DFT favors the dibridge[7] geometry but the potential energy surface is rather smooth and other adsorption geometries may coexist. DFT also reveals a pronounced dearomatization and charge transfer from the adsorbed molecule into the nickel surface. Dehydrogenation occurs in two steps, with two desorption peaks at approximately 450 and 600 K. The first step is due to partial dehydrogenation generating active hydrocarbon species that at higher temperatures migrates over the surface forming graphene. The graphene formation is accompanied by desorption of hydrogen in the high temperature TPD peak. The formation of graphene effectively passivates the surface both for hydrogen adsorption and naphthalene dissociation. In conclusion, the obtained results on the model naphthalene and Ni(111) system, provides insight into elementary steps of naphthalene adsorption, dehydrogenation, and carbon passivation, which may serve as a good starting point for rational design, development and optimization of the Ni catalyst surface, as well as process conditions, for the aromatic hydrocarbon reforming process.
Surface coated magnetite nanoparticles (Fe3O4 NPs) with 3-mercaptopropionic acid were immobilized on amidoximated polyacrilonitrile (APAN) nanofibers using electrospinning followed by crosslinking.
The temperature dependent dehydrogenation of naphthalene on Ni(111) has been investigated using vibrational sum-frequency generation spectroscopy, X-ray photoelectron spectroscopy, scanning tunneling microscopy, and density functional theory with the aim of discerning the reaction mechanism and the intermediates on the surface. At 110 K, multiple layers of naphthalene adsorb on Ni(111); the first layer is a flat lying chemisorbed monolayer, whereas the next layer(s) consist of physisorbed naphthalene. The aromaticity of the carbon rings in the first layer is reduced due to bonding to the surface Ni-atoms. Heating at 200 K causes desorption of the multilayers. At 360 K, the chemisorbed naphthalene monolayer starts dehydrogenating and the geometry of the molecules changes as the dehydrogenated carbon atoms coordinate to the nickel surface; thus, the molecule tilts with respect to the surface, recovering some of its original aromaticity. This effect peaks at 400 K and coincides with hydrogen desorption. Increasing the temperature leads to further dehydrogenation and production of H 2 gas, as well as the formation of carbidic and graphitic surface carbon.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.