Poly(lactic acid) (PLA) is a biobased polyester with ever-growing applications in the fields of packaging and medicine. Despite its popularity, it suffers from inherent brittleness, a very slow degradation rate and a high production cost. To tune the properties of PLA, block copolymers with poly(propylene adipate) (PPAd) prepolymer were prepared by polymerizing L-lactide and PPAd oligomers via reactive extrusion (REX) in a torque rheometer. The effect of reaction temperature and composition on the molecular weight, chemical structure, and physicochemical properties of the copolymers was studied. The introduction of PPAd successfully increased the elongation and the biodegradation rate of PLA. REX is an efficient and economical alternative method for the fast and continuous synthesis of PLA-based copolymers with tunable properties.

In this work, we study a series of sustainable block copolymers based on polylactide, PLA, and poly(propylene adipate), PPAd, both polymers being prepared from renewable resources. Envisaging wide range of...

Polymers are essential materials in our daily life. The synthesis of value-added polymers is mainly performed from fossil fuel-derived monomers. However, the adoption of the circular economy model based on the bioeconomy will reduce the dependence on fossil fuels. In this context, biorefineries have emerged to convert biomass into bioenergy and produce high value-added products, including molecules that can be further used as building blocks for the synthesis of biopolymers and bioplastics. The achievement of catalytic systems able to polymerize the natural monomer counterparts, such as terpenes or terpenoids, is still a challenge in the development of polymers with good mechanical, thermal, and chemical properties. This review describes the most common types of bioplastics and biopolymers and focuses specifically on the polymerization of terpenes and terpenoids, which represent a source of promising monomers to create bio-based polymers and copolymers.

This article presents an evaluation of bast fiber properties conditioned by the selection of a retting method in terms of meeting requirements for the final application of the fibers as composite reinforcement. Two different methods of fiber extraction were used in the experiment: dew retting and osmotic degumming. The fibrous material was extracted from flax (Modran variety) and hemp (Bialobrzeskie variety). In addition, retted kenaf fibers (from China) were evaluated for the comparison of fiber properties. The properties of the retted and degummed fibers were evaluated according to relevant valid standards regarding color, linear mass, breaking tenacity, aspect ratio, microscopic images and chemical composition, which included the determination of wax and fat, cellulose, hemicellulose, lignin and pectin content and the thermogravimetric analysis coupled with Fourier transform infrared spectroscopy technique. The Attenuated Total Reflection FTIR spectroscopic technique was used for the characterization of the fibers. Also, fogging and volatile organic compound (VOC) emissions were tested in order to evaluate the suitability of the bast fiber for composite formation. The results of the study proved that osmotic degumming applied for bast fiber extraction improves significantly the fiber quality in terms of color, odor, aspect ratio and VOC emission. The aspect ratio of osmotically degummed flax fibers increased by about 46% and hemp fibers by about 22% in comparison with dew-retted fibers. VOC emission of osmotically degummed hemp decreased by about 35%, but in the case of flax fibers, increasing of VOC has been observed. For this reason, osmotically degummed fibers can be recommended as more suitable for composite reinforcement.

This work describes the synthesis of poly(lactic acid) by the ring-opening polymerization of L-lactide in the presence of oligo(butylene succinate) with two different molecular weights (Mn = 6100 and 16300 g/mol) as a macroinitiator during reactive processing. The macroinitiators were added in concentrations 1 wt%, 2.5 wt%, 5 wt%, 10 wt% and 15 wt% in respect to the L-lactide mass in the premix. The properties of the received copolymers were extensively studied with spectroscopic techniques, GPC, DSC, XRD, TGA as well as nanoindentation. Blocky copolymers were received with number average molecular weights ranging from 30 to 100 kg/mol, which decreased with increasing the PBSu content in the feed. The introduction of the flexible PBSu chains decreased the single glass transition detected, while DSC and XRD gave indications that both components crystallized in the copolymers with PBSu premix content > 5 wt%. Thermal stability was maintained and depended on the composition and molecular weight. Nanoindentation showed that despite the decreasing trend of hardness and elastic modulus with increasing PBSu content, the PLA-PBSu 2.5% copolymers had simultaneously higher elasticity modulus and strength compared to the other compositions, possibly because of a complementary effect of their high molecular weight and crystallinity. These copolymers were promising for production with continuous reactive extrusion, a novel, fast and economically viable method to commercially produce PLA-based polymers.