Establishing new reactivity map descriptor of TOF–SD for PGM-free Fe–N–C catalysts ORR activity.

HAL is a multi-disciplinary open access archive for the deposit and dissemination of scientific research documents, whether they are published or not. The documents may come from teaching and research institutions in France or abroad, or from public or private research centers. L'archive ouverte pluridisciplinaire HAL, est destinée au dépôt et à la diffusion de documents scientifiques de niveau recherche, publiés ou non, émanant des établissements d'enseignement et de recherche français ou étrangers, des laboratoires publics ou privés.

We report and study the translation of exceptionally high catalytic oxygen electroreduction activities of molybdenum-doped octahedrally shaped PtNi­(Mo) nanoparticles from conventional thin-film rotating disk electrode screenings (3.43 ± 0.35 A mgPt –1 at 0.9 VRHE) to membrane electrode assembly (MEA)-based single fuel cell tests with sustained Pt mass activities of 0.45 A mgPt –1 at 0.9 Vcell, one of the highest ever reported performances for advanced shaped Pt alloys in real devices. Scanning transmission electron microscopy with energy dispersive X-ray analysis (STEM-EDX) reveals that Mo preferentially occupies the Pt-rich edges and vertices of the element-anisotropic octahedral PtNi particles. Furthermore, by combining in situ wide-angle X-ray spectroscopy, X-ray fluorescence, and STEM-EDX elemental mapping with electrochemical measurements, we finally succeeded to realize high Ni retention in activated PtNiMo nanoparticles even after prolonged potential-cycling stability tests. Stability losses at the anodic potential limits were mainly attributed to the loss of the octahedral particle shape. Extending the anodic potential limits of the tests to the Pt oxidation region induced detectable Ni losses and structural changes. Our study shows on an atomic level how Mo adatoms on the surface impact the Ni surface composition, which, in turn, gives rise to the exceptionally high experimental catalytic ORR reactivity and calls for strategies on how to preserve this particular surface composition to arrive at performance stabilities comparable with state-of-the-art spherical dealloyed Pt core–shell catalysts.

The number of catalytically active sites (site density, SD) and the catalytic turnover frequency (TOF) are critical for meaningful comparisons between catalytic materials and their rational improvement. SD and TOF numbers have remained elusive for PGM-free, metal/nitrogen-doped porous carbon electrocatalysts (MNC), in particular, FeNC materials that are now intensively investigated and widely utilized to catalyze the oxygen reduction reaction (ORR) in fuel cell cathodes. Here, we apply CO cryo sorption and desorption to evaluate SD and TOF numbers of a state-of-art FeNC ORR electrocatalyst with atomically dispersed coordinative FeN x (x ≤ 4) sites in acid and alkaline conditions. More specifically, we study the impact of thermal pretreatment conditions prior to assessing the number of sorption-active FeN x sites. We show that the pretreatment temperature sensitively affects the CO sorption uptake through a progressive thermal removal of airborne adsorbates, which, in turn, controls the resulting catalytic SD numbers. We correlate CO uptake with CO desorption and analyze the observed temperature-programmed desorption characteristics. The CO uptakes increased from 45 nmol·mg–1 catalyst at 300 °C cleaning to 65 nmol·mg–1 catalyst at 600 °C cleaning, where it leveled off. These values were converted into apparent SD values of 2.7 × 1019 to 3.8 × 1019 surface sites per gram catalyst. Because of similar ORR activity of the pristine catalyst and of the sample after 600 °C cleaning step, we conclude that the nature and number of surface FeN x sites remained largely unaffected up to 600 °C and that cleaning to less than 600 °C was insufficient to free the sites from previously adsorbed species, completely or partially impeding CO adsorption. Cleaning beyond that temperature, however, led to undesired chemical modifications of the FeN x moieties, resulting in higher TOF. In all, this study identifies and recommends a practical and useful protocol for the accurate evaluation of catalytic SD and TOF parameters of PGM-free ORR electrocatalyst, which enables a more rational future catalyst development and improvement.

The experimental development of catalytically ever-more active platinum group metal (PGM)-free materials for the oxygen reduction reaction (ORR) at fuel cell cathodes has been until recently a rather empirical iteration of synthesis and testing. Here, we present how kinetic reactivity maps based on kinetic descriptors of PGM-free single-metal-site ORR electrocatalysts can help to better understand the origin of catalytic reactivity and help to derive rational synthetic guidelines toward improved catalysts. Key in our analysis are the catalytic surface site density (SD) and the catalytic turnover frequency (TOF) in their role as controlling kinetic parameters for the ORR reactivity of PGM-free nitrogen-coordinated single-metal M-site carbon (MNC) catalysts. SD–TOF plots establish two-dimensional reactivity maps. We also consider the ratio between SD and the total number of single-metal sites in the bulk, referred to as the site utilization factor, which we propose as another guiding parameter for optimizing the synthesis of MNC catalysts. Exemplified by two sets of FeNC, CoNC, and SnNC catalysts prepared using two distinctly different N- and C-precursor material classes (Zn-based zeolitic imidazolate frameworks and covalent polyaniline), we comparatively diagnose the intrinsic kinetic ORR parameters as well as structural, morphological, and chemical properties. From there, we derive and discuss possible synthetic guidelines for further improvements. Our approach can be extended to other families of catalysts and may involve kinetic performance data of idealized liquid-electrolyte cells as well as gas diffusion layer-type flow cells.