Electrostatic ion cyclotron wave fields are determined in a magnetized and weakly collisional plasma. A phased-locked Laser Induced Fluorescence (LIF) diagnostic is used to directly measure the wave perturbed ion velocity distribution. Comparing these local LIF measurements with a theoretical model uniquely determines the wave parameters, such as the wave potential, the three-dimensional wave vector, and the effective wave damping. The self-consistent wave–particle interaction is modeled by Boltzmann–Poisson equations in the limit of weak collisions. The wave parameters determined from local measurements agree with those determined from spatial scans.
Articles you may be interested inDetection of electron energy distribution function anisotropy in a magnetized electron cyclotron resonance plasma by using a directional Langmuir probe Phys. Plasmas 21, 073510 (2014); 10.1063/1.4890350Optical emission spectroscopy and Langmuir probe diagnostics of CH3F/O2 inductively coupled plasmasThe Langmuir probe as a diagnostic of the electron component within low temperature laser ablated plasma plumes Rev.Diagnostics of inductively amplified magnetron discharges by optical emission, absorption spectroscopy, and Langmuir probe measurements Langmuir probe theory, adapted to magnetized, partially ionized, low temperature processing plasmas with radial diffusion dominated by electron-neutral collisions, was verified in electron cyclotron resonance ͑ECR͒ plasmas. Plasma parameters such as plasma potential, electron temperature, plasma density, and the ratio of electron saturation current to ion saturation current (I e */I i *) were measured by single-sided planar probe in various ECR plasmas ͑H 2 , He, N 2 , O 2 , Ar, and CF 4 ͒. The neutral pressure was varied between 0.5 and 8.5 mTorr and the microwave power between 170 and 1250 W with good matching conditions; the reflected power was kept at less than 3% of the input power. The measured ratios of I e */I i * , and other plasma parameters were consistent with the probe theory for pressures greater than 2.0 mTorr for various plasmas of Ar, He, H 2 , and N 2 . These results indicate that the electron-neutral collisional probe theory works well for magnetized ECR plasmas ͑magnetic flux densities of 0.8-1.0 kG͒.
The electron density, the electron kinetic energy, the particle motion, and electric fields in a coaxial positive-polarity plasma opening switch (POS) were studied using spectroscopic diagnostics. A gaseous source that injects the plasma radially outward from inside the inner POS electrode was developed. The plasma was locally seeded with various species, desired for the various measurements allowing for axial, radial, and azimuthal resolutions both prior to and during the 180 ns long current pulse. The electron density was determined from particle ionization times and the electron energy from line intensities and time dependent collisional-radiative calculations. Fluctuating electric fields were studied from Stark broadening. The ion velocity distributions were obtained from emission-line Doppler broadenings and shifts. The early ion motion, the relatively low ion velocities and the nearly linear velocity dependence on the ion charge-to-mass ratio, leads to the conclusion that the magnetic field penetrates the plasma early in the pulse. The ion velocity dependence on the axial location were thus used to infer the time dependent axial distribution of the magnetic field, indicating the formation of a relatively high current density at the load-side edge of the plasma. This is expected to cause plasma acceleration towards the load, found to be supported by charge-collector measurements. The fast magnetic field penetration could be explained by mechanisms based on the Hall effect.
Real-time etch rate of thin transparent films is determined within seconds by an in-situ two-color laser interferometer. The use of two colors improves the accuracy of the calculated rates, provides an absolute measure of film thickness for endpoint prediction, and differentiates between etching and deposition. The tool state parameters, rf power to the antenna and the wafer stage, gas pressure and flow rates, are computer controlled and monitored. Real-time etch rate characterization is obtained by monitoring the etch dependence on varying tool state parameters. The density of the etch radicals, chlorine and fluorine, is obtained with xenon and argon actinometry using optical emission and mass spectra. An etch rate model, based on the input power to the wafer stage and the relative density of the etch radicals, is used to develop a model-based real-time control algorithm. This algorithm has been used to control the etch rate of unpatterned polysilicon and SiO2.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.