Nanofi bers consisting of the bulk heterojunction organic photovoltaic (BHJ-OPV) electron donor-electron acceptor pair poly(3-hexylthiophene):phenyl-C 61 -butyric acid methyl ester (P3HT:PCBM) are produced through a coaxial electrospinning process. While P3HT:PCBM blends are not directly electrospinnable, P3HT:PCBM-containing fi bers are produced in a coaxial fashion by utilizing polycaprolactone (PCL) as an electrospinnable sheath material. Pure P3HT:PCBM fi bers are easily obtained after electrospinning by selectively removing the PCL sheath with cyclopentanone (average diameter 120 ± 30 nm). These fi bers are then incorporated into the active layer of a BHJ-OPV device, which results in improved short-circuit current densities, fi ll factors, and power-conversion effi ciencies (PCE) as compared to thin-fi lm devices of identical chemical composition. The best-performing fi ber-based devices exhibit a PCE of 4.0%, while the best thin-fi lm devices have a PCE of 3.2%. This increase in device performance is attributed to the increased in-plane alignment of P3HT polymer chains on the nanoscale, caused by the electrospun fi bers, which leads to increased optical absorption and subsequent exciton generation. This methodology for improving device performance of BHJ-OPVs could also be implemented for other electron donor-electron acceptor systems, as nanofi ber formation is largely independent of the PV material.
Reflectins are a family of proteins found in the light manipulating cells of cephalopods. These proteins are made up of a series of conserved repeats that contain highly represented amino acids thought to be important for function. Previous studies demonstrated that recombinant reflectins cast into thin films produced structural colors that could be dynamically modulated via changing environmental conditions. In this study, we demonstrate light scattering from reflectin films following exposure to a series of water vapor pulses. Analysis of film surface topography shows that the induction of light scatter is accompanied by self-assembly of reflectins into micro- and nanoscale features. Using a reductionist strategy, we determine which reflectin repeats and sub-repeats are necessary for these events following water vapor pulsing. With this approach, we identify a singly represented, 23-amino acid region in reflectins as being sufficient to recapitulate the light scattering properties observed in thin films of the full-length protein. Finally, the aqueous stability of reflectin films is leveraged to show that pre-exposure to buffers of varying pH can modulate the ability of water vapor pulses to induce light scatter and protein self-assembly.
Regenerated silk fibroin, a biopolymer derived from silkworm cocoons, is a versatile material that has been widely explored for a number of applications (e.g., drug delivery, tissue repair, biocompatible electronics substrates, and optics) due to its attractive biochemical properties and processability. Here, we report on the free-form printing of silk-based, 3D microstructures through multiphoton lithography. Utilizing multiphoton lithography in conjunction with specific photoinitiator chemistry and postprint cross-linking, a number of microarchitectures were achieved including self-supporting fibroin arches. Further, the straightforward production of high fidelity and biofunctional protein architectures was enabled through the printing of aqueous fibroin/immunoglobulin solutions.
In this study, we utilize plasma-enhanced chemical vapor deposition (PECVD) for the deposition of nanostructures composed of diphenylalanine. PECVD is a solvent-free approach and allows sublimation of the peptide to form dense, uniform arrays of peptide nanostructures on a variety of substrates. The PECVD deposited d-diphenylalanine nanostructures have a range of chemical and physical properties depending on the specific discharge parameters used during the deposition process.
Wound healing is a complex, multistep process that can be summarized into three stages, namely, hemostasis and inflammation, proliferation, and finally, tissue remodeling. Battlefield wound healing demands rapid hemostasis using clotting or cauterizing agents to immediately limit blood loss, but this occurs at the expense of proper tissue repair beyond hemostasis. Layered silicate clays such as kaolin and montmorillonite (MMT) have been previously shown to induce blood clotting due to their ability to form charged interactions with clotting factors. The charge characteristics of sodium MMT (Na-MMT) also enable functionalization with active biomolecules. Herein we functionalized Na-MMT with epidermal growth factor (EGF) via ion exchange reaction to create a nanocomposite (MMT-EGF) with approximately 0.004 EGF molecules per Na(+) exchange site and conduct biochemical analyses of keratinocytes after treatment with MMT-EGF. Our results demonstrate that EGF immobilized on MMT retains the ability to activate the epidermal growth factor receptor (EGRF), causing phosphorylation of the AKT and MEK1 pathways, as well as upregulation of its downstream target gene expression involved in cell growth and migration. This study also shows that like EGF, MMT-EGF treatment can stimulate cell migration in vitro, which is dependent on ERK1/2 phosphorylation.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.