No abstract

This aims of this study were (I) to determine the velocity variable and regression model which best fit the load-velocity relationship during the free-weight prone bench pull exercise, (II) to compare the reliability of the velocity attained at each percentage of the one-repetition maximum (1RM) between different velocity variables and regression models, and (III) to compare the within- and between-subject variability of the velocity attained at each %1RM. Eighteen men (14 rowers and four weightlifters) performed an incremental test during the free-weight prone bench pull exercise in two different sessions. General and individual load-velocity relationships were modelled through three velocity variables (mean velocity [MV], mean propulsive velocity [MPV] and peak velocity [PV]) and two regression models (linear and second-order polynomial). The main findings revealed that (I) the general (Pearson's correlation coefficient [ r ] range = 0.964–0.973) and individual (median r = 0.986 for MV, 0.989 for MPV, and 0.984 for PV) load-velocity relationships were highly linear, (II) the reliability of the velocity attained at each %1RM did not meaningfully differ between the velocity variables (coefficient of variation [CV] range = 2.55–7.61% for MV, 2.84–7.72% for MPV and 3.50–6.03% for PV) neither between the regression models (CV range = 2.55–7.72% and 2.73–5.25% for the linear and polynomial regressions, respectively), and (III) the within-subject variability of the velocity attained at each %1RM was lower than the between-subject variability for the light-moderate loads. No meaningful differences between the within- and between-subject CVs were observed for the MV of the 1RM trial (6.02% vs . 6.60%; CV ratio = 1.10), while the within-subject CV was lower for PV (6.36% vs . 7.56%; CV ratio = 1.19). These results suggest that the individual load-MV relationship should be determined with a linear regression model to obtain the most accurate prescription of the relative load during the free-weight prone bench pull exercise.

Cuevas-Aburto, J, Jukic, I, Chirosa-Ríos, LJ, González-Hernández, JM, Janicijevic, D, Barboza-González, P, Guede-Rojas, F, and García-Ramos, A. Effect of traditional, cluster, and rest redistribution set configurations on neuromuscular and perceptual responses during strength-oriented resistance training. J Strength Cond Res 36(6): 1490–1497, 2022—This study aimed to compare the acute effect of traditional (TR), cluster (CL), and rest redistribution (RR) set configurations on neuromuscular and perceptual measures of fatigue. Thirty-one resistance-trained men randomly performed a Control session and 3 experimental sessions consisting of the squat (SQ) and bench press (BP) exercises performed against the 10 repetition maximum load using TR (3 sets of 6 repetitions; 3 minutes of interset rest), CL (3 sets of 6 repetitions; 30 seconds of intraset rest every 2 repetitions; 3 minutes of interset rest), and RR (9 sets of 2 repetitions; 45 seconds of interset rest) set configurations. A significant effect of “set configuration” (p = 0.002) was observed for barbell velocity. The average velocity of the training session was lower for TR compared with CL (% difference = 5.09% in SQ and 5.68% in BP) and RR (% difference = 5.92% in SQ and 2.71% in BP). The 3 set configurations induced comparable decrements in countermovement jump height (% difference from −6.0% to −8.1%) and throwing velocity (% difference from −0.6% to −1.2%). Ratings of perceived exertion (RPE-10) values collected after the sets were higher for TR (SQ: 6.9 ± 0.7 a.u.; BP: 6.8 ± 0.8 a.u.) compared with CL (SQ: 6.2 ± 0.8 a.u.; BP: 6.4 ± 0.7 a.u.) and RR (SQ: 6.2 ± 0.8 a.u.; BP: 6.6 ± 0.9 a.u.), while the session RPE did not differ between the set configurations (p = 0.595). CL and RR set configurations allow for higher velocities and lower RPE values during resistance training sessions not performed to failure in comparison with a TR set configuration.

BackgroundThe aim of this study was to examine whether the addition of very light loads for modeling the force–velocity (F–V) relationship during the bench press (BP) exercise can confirm its experimental linearity as well as to increase the reliability and concurrent validity of the F–V relationship parameters (maximum force (F0), maximum velocity (V0), F–V slope, and maximum power (Pmax)).MethodThe F–V relationship of 19 healthy men were determined using three different methods: (I) 6-loads free method: six loads performed during the traditional free-weight BP exercise (≈ 1–8–29–39–49–59 kg), (II) 4-loads free method: four loads performed during the traditional free-weight BP exercise (≈ 29–39–49–59 kg), and (III) 4-loads Smith method: four loads performed during the ballistic bench press throw exercise in a Smith machine (≈ 29–39–49–59 kg).ResultsThe linearity of the F–V relationship was very high and comparable for the three F–V methods (p = 0.204; median Pearson’s correlation coefficient (r) = 0.99). The three methods were ranked from the most to the least reliable as follows: 6-loads free (coefficient of variation (CV) range = 3.6–6.7%) > 4-loads Smith (CV range = 4.6–12.4%) > 4-loads free (CV range = 3.8–14.5%). The higher reliability of the 6-loads free method was especially pronounced for F–V slope (CVratio ≥ 1.85) and V0 (CVratio ≥ 1.49) parameters, while the lowest difference in reliability was observed for F0 (CVratio ≤ 1.27). The 6-loads free and 4-loads free methods showed a very high concurrent validity respect to the 4-loads Smith method for F0 and Pmax (r ≥ 0.89), a moderate validity for the F–V slope (r = 0.66–0.82), and a low validity for V0 (r ≤ 0.37).DiscussionThe routine testing of the F–V relationship of upper-body muscles through the BP exercise should include trials with very light loading conditions to enhance the reliability of the F–V relationship.

No abstract