The type of relative motion between the bearing surfaces of prosthetic joints is known to strongly influence their wear behaviour. The previously validated 16-station wear simulator of the pin-on-disc type, called RandomPOD, was used to study the wear of a conventional, gamma-sterilized ultra-high molecular weight polyethylene (UHMWPE). The counterface was polished CoCr and the lubricant was diluted calf serum. Two test conditions were compared, random motion/random load and circular translation/static load. With random motion, the accumulated change of the direction of sliding was 2.8 times higher than that with circular translation. The test duration with both test conditions was 880 h. Random motion/random load resulted in a mean wear factor 23 per cent higher than that produced with circular translation/static load. The difference was statistically significant. The wear mechanisms however were similar and in agreement with clinical observations. As earlier studies have shown that the type of load is of secondary importance, the present study confirms the earlier findings that the type of relative motion is tribologically of fundamental importance. In particular, the complex, yet biomechanically realistic non-cyclic motion, represented by the random track, resulted in a wear factor significantly higher than that produced by a fixed slide track shape.
Effects of the plate material, surface roughness and measuring gap height on static and dynamic yield stresses of a magnetorheological (MR) fluid were investigated with a commercial plate–plate magnetorheometer. Magnetic and non-magnetic plates with smooth (Ra ∼ 0.3 μm) and rough (Ra ∼ 10 μm) surface finishes were used. It was shown by Hall probe measurements and finite element simulations that the use of magnetic plates or higher gap heights increases the level of magnetic flux density and changes the shape of the radial flux density profile. The yield stress increase caused by these factors was determined and subtracted from the measured values in order to examine only the effect of the wall characteristics or the gap height. Roughening of the surfaces offered a significant increase in the yield stresses for non-magnetic plates. With magnetic plates the yield stresses were higher to start with, but roughening did not increase them further. A significant part of the difference in measured stresses between rough non-magnetic and magnetic plates was caused by changes in magnetic flux density rather than by better contact of the particles to the plate surfaces. In a similar manner, an increase in gap height from 0.25 to 1.00 mm can lead to over 20% increase in measured stresses due to changes in the flux density profile. When these changes were compensated the dynamic yield stresses generally remained independent of the gap height, even in the cases where it was obvious that the wall slip was present. This suggests that with MR fluids the wall slip cannot be reliably detected by comparison of flow curves measured at different gap heights.
Articles you may be interested indc-and ac-magnetic field-induced strain effects in ferromagnetic shape memory composites of Ni-Mn-Ga single crystal and polyurethane polymer J. Appl. Phys. 107, 09A942 (2010); 10.1063/1.3357408 Large magnetic-field-induced strains in Ni-Mn-Ga nonmodulated martensite Appl. Phys. Lett. 95, 104103 (2009); 10.1063/1.3227661Acoustic-assist effect on magnetic threshold field and twinning-yield stress of Ni-Mn-Ga single crystals
This paper presents an innovative solution for bounce reduction between a robotic leg and the ground by means of a semi-active compliant foot. The aim of this work is to enhance the controllability and the balance of a legged robot by improving the traction between the foot tip and the ground. The compliant foot is custom-designed for quadruped walking robots and it consists of a linear spring and a magnetorheological (MR) damper. By utilizing magnetorheological technology in the damper element, the damping coefficient of the compliant foot can be altered across a wide range without any additional moving parts. The content of this paper is twofold. In the first part the design, a prototype and a model of the semi-active compliant foot are presented, and the performance of the magnetorheological damper is experimentally studied in quasi-static and dynamic cases. Based on the quasi-static measurements, the damping force can be controlled in a range from 15 N to 310 N. From the frequency response measurements, it can be shown that the controllable damping force has a bandwidth higher than 100 Hz. The second part of this paper presents an online stiffness identification algorithm and a mathematical model of the robotic leg. A critical damping control law is proposed and implemented in order to demonstrate the effectiveness of the device that makes use of smart materials. Further on, drop tests have been carried out to assess the performance of the proposed control law in terms of bounce reduction and settling time. The results demonstrate that by real-time control of the damping force 98% bounce reduction with settling time of 170 ms can be achieved.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.