Diffusors are widely used optical components having numerous applications. They are commonly used to homogenize light beams and to create particular intensity distributions. The angular scattering profile of bulk scattering diffusing materials is determined by three bulk scattering parameters that are, however, not commonly available. This hampers an accurate implementation of bulk diffusors in ray tracing simulations. In this paper, the bulk scattering parameters of a concentration series of milk diluted with water were determined with the inverse adding-doubling method. Using these values as input, the macroscopic angular scattering profile was simulated using ray tracing software. The simulation results were compared to experimental data, and a good agreement between measured and simulated data was found. The method was also proven to be successful when applied to commercial diffusors.
Among the complete bidirectional reflectance distribution function (BRDF), visual gloss is principally related to physical reflection characteristics located around the specular reflection direction. This particular part of the BRDF is usually referred to as the specular peak. A good starting point for the physical description of gloss could be to measure the reflection properties around this specular peak. Unfortunately, such a characterization is not trivial, since for glossy surfaces the width of the specular peak can become very narrow (typically a full width at half maximum inferior to 0.5° is encountered). In result, new BRDF measurement devices with a very small solid angle of detection are being introduced. Yet, differences in the optical design of BRDF measurement instruments engender different measurement results for the same specimen, complicating direct comparison of the measurement results.This issue is addressed in this paper. By way of example, BRDF measurement results of two samples, one being matte and the other one glossy, obtained by use of two high level goniospectrophotometers with a different optical design, are described. Important discrepancies in the results of the glossy sample are discussed. Finally, luminance maps obtained from renderings with the acquired BRDF data are presented, exemplifying the large visual differences that might be obtained. This stresses the metrological aspects that must be known for using BRDF data. Indeed, the comprehension of parameters affecting the measurement results is an inevitable step towards progress in the metrology of surface gloss, and thus towards a better metrology of appearance in general.
Light-emitting diodes (LEDs) are becoming increasingly important for general lighting applications. The remote phosphor technology, with the phosphor located at a distance from the LEDs, offers an increased extraction efficiency for phosphor converted LEDs compared to intimate phosphor LEDs where the phosphor is placed directly on the die. Additionally, the former offers new design possibilities that are not possible with the latter. In order to further improve the system efficiency of remote phosphor LEDs, realistic simulation models are required to optimize the actual performance. In this work, a complete characterization of a remote phosphor converter (RPC) consisting of a polycarbonate diffuser plate with a phosphor coating on one side via the bi-directional scattering distribution function (BSDF) is performed. Additionally, the bi-spectral BSDF which embraces the wavelength conversion resulting from the interaction of blue light with the RPC is determined. An iterative model to predict the remote phosphor module power and photon budget, including the recuperation of backward scattered light by a mixing chamber, is introduced. The input parameters for the model are the bi-spectral BSDF data for the RPC, the emission of the blue LEDs and the mixing chamber efficiency of the LED module. A good agreement between experimental and simulated results was found, demonstrating the potential of this model to analyze the system efficiency with errors smaller than 4%.
The reliability of ray tracing simulations is strongly dependent on the accuracy of the input data such as the bidirectional reflectance distribution function (BRDF). Software developers offer the possibility to implement BRDF data in different ways, ranging from simple predefined functions to detailed tabulated data. The impact of the accuracy of the implemented reflectance model on ray tracing simulations has been investigated. A light-emitting diode device including a frequently employed diffuse reflector [microcellular polyethylene terephthalate (MCPET)] was constructed. The luminous intensity distribution (LID) and luminance distribution from a specific viewpoint were measured with a near-field goniophotometer. Both distributions were also simulated by use of ray tracing software. Three different reflection models of MCPET were introduced, varying in complexity: a diffuse model, a diffuse/specular model, and a model containing tabulated BRDF data. A good agreement between the measured and simulated LID was found irrespective of the applied model. However, the luminance distributions only corresponded when the most accurate BRDF model was applied. This proves that even for diffuse reflective materials, a simple BRDF model may only be employed for simulations of the LID; for evaluation of luminance distributions, more complex models are needed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.