Silicon is considered a most promising anode material for overcoming the theoretical capacity limit of carbonaceous anodes. The use of nanomethods has led to significant progress being made with Si anodes to address the severe volume change during (de)lithiation. However, less progress has been made in the practical application of Si anodes in commercial lithium‐ion batteries (LIBs). The drastic increase in the energy demands of diverse industries has led to the co‐utilization of Si and graphite resurfacing as a commercially viable method for realizing high energy. Herein, we highlight the necessity for the co‐utilization of graphite and Si for commercialization and discuss the development of graphite/Si anodes. Representative Si anodes used in graphite‐blended electrodes are covered and a variety of strategies for building graphite/Si composites are organized according to their synthetic methods. The criteria for the co‐utilization of graphite and Si are systematically presented. Finally, we provide suggestions for the commercialization of graphite/Si combinations.

Engineered polycrystalline electrodes are critical to the cycling stability and safety of lithium-ion batteries, yet it is challenging to construct high-quality coatings at both the primary-and secondaryparticle levels. Here, we present a room-temperature synthesis route to achieve full surface coverage of secondary particles and facile infusion into grain boundaries, thus offering a complete "coatingplus-infusion" strategy. Cobalt boride metallic glass is successfully applied to Ni-rich layered cathode LiNi 0.8 Co 0.1 Mn 0.1 O 2 . It dramatically improves the rate capability and cycling stability, including under high-discharge-rate and elevated-temperature conditions and in pouch full cells.The superior performance originates from simultaneous suppression of microstructural degradation of intergranular cracking and side reactions with electrolyte. Atomistic simulations identified the critical role of strong selective interfacial bonding, which offers not only a large chemical driving force to ensure uniform reactive wetting and facile infusion but also lowered the surface/interface 2 oxygen activity, contributing to the exceptional mechanical and electrochemical stabilities of the infused electrode.

An epitaxy layer on the LiNi0.8Co0.1Mn0.1O2 cathode significantly suppressed the nickel-ion crossover, which enhanced the structural/electrochemical stability at high temperature.

A practical solution is presented to increase the stability of 4.45 V LiCoO 2 via high-temperature Ni doping, without adding any extra synthesis step or cost. How a putative uniform bulk doping with highly soluble elements can profoundly modify the surface chemistry and structural stability is identified from systematic chemical and microstructural analyses. This modification has an electronic origin, where surface-oxygen-loss induced Co reduction that favors the tetrahedral site and causes damaging spinel phase formation is replaced by Ni reduction that favors octahedral site and creates a better cation-mixed structure. The findings of this study point to previously unspecified surface effects on the electrochemical performance of battery electrode materials hidden behind an extensively practiced bulk doping strategy. The new understanding of complex surface chemistry is expected to help develop higherenergy-density cathode materials for rechargeable batteries.

Conventional nickel‐rich cathode materials suffer from reaction heterogeneity during electrochemical cycling particularly at high temperature, because of their polycrystalline properties and secondary particle morphology. Despite intensive research on the morphological evolution of polycrystalline nickel‐rich materials, its practical investigation at the electrode and cell levels is still rarely discussed. Herein, an intrinsic limitation of polycrystalline nickel‐rich cathode materials in high‐energy full‐cells is discovered under industrial electrode‐fabrication conditions. Owing to their highly unstable chemo‐mechanical properties, even after the first cycle, nickel‐rich materials are degraded in the longitudinal direction of the high‐energy electrode. This inhomogeneous degradation behavior of nickel‐rich materials at the electrode level originates from the overutilization of active materials on the surface side, causing a severe non‐uniform potential distribution during long‐term cycling. In addition, this phenomenon continuously lowers the reversibility of lithium ions. Consequently, considering the degradation of polycrystalline nickel‐rich materials, this study suggests the adoption of a robust single‐crystalline LiNi0.8Co0.1Mn0.1O2 as a feasible alternative, to effectively suppress the localized overutilization of active materials. Such an adoption can stabilize the electrochemical performance of high‐energy lithium‐ion cells, in which superior capacity retention above ≈80% after 1000 cycles at 45 °C is demonstrated.