The paper shows the results of the research obtained by physical and mathematical modeling of steel flow and mixing in the tundish. Two‐strand continuous casting tundish was under consideration. It has been working in one of polish steel plants. The change of concast slab assortment was caused by the changeable market terms. So, the tundish with the new system of steel flow controller was needed. Up to now baffles with the notch have played this role. Their placement cause the excessive consumption of the lining of the tundish front line. As a consequence the turbulence inhibitor (TI) was applied. Four different types of this inhibitor were designed. As a result of the experimental measurements and numerical simulations, the RTD curves of F‐type were obtained. Basing on these curves time constants for examined types were determined. Additionally, the research results were complemented by the E‐type curves. The percentage participations of dead volume flow, dispersed plug flow, and well‐mixed volume flow were calculated. The research gives possibility to estimate the designed TIs and their influence on the tundish work.

The tundish plays a major role in the continuous casting process. The flow in a tundish has a very substantial effect on the quality of the final product and on efficient casting conditions. Efforts are being made worldwide to obtain the most favourable shape of tundish interior by using dams, weirs and gas curtains. The aim of these flow control devices is to reduce the dead zone areas and improve the conditions for the separation of non‐metallic inclusions. Numerous model studies are being carried out to explain the effect of the tundish working space shape and steel flow conditions on the inclusions floating processes. The presented article shows the results of investigations performed to obtain the mass exchange characteristics in the investigated tundish. The measurements were done directly at the steel plant during normal working conditions. By controlling the changing content of manganese in steel, the residence time distribution (RTD) characteristics were acquired. The RTD characteristics are also obtained with a water model of the tundish with dimensional scale of 1:3. Parallel to the water model, numerical simulation based on mathematical modelling of fluid flow, relying on the system of differential equations, is employed in the research work. Numerical simulations were carried out with the finite‐volume commercial code FLUENT using the standard k‐ε turbulence model. The primary purpose of the investigations carried out is to present the characteristics describing the transitory zone in a six‐strand tundish. It is shown that the F‐curve, describing the transitory zone, can be obtained by using different measurement techniques. Tracer concentration characteristics for the model of tundish obtained from both modelling techniques ‐ physical as well as numerical ‐ are very similar.

This study shows research results of behaviors of nonmetallic inclusions (NMIs) in a tundish represented by water model. The object under investigation is a two‐strand trough‐type continuous casting tundish operating in one of the Polish steel plants. Hollow glass microspheres with diameters ranging from 10 to 140 μm are used for testing, which represents the NMIs. The distribution process of microspheres is investigated; the qualitative analysis (visualization) and quantitative analysis (using a laser particle counter) of microsphere distribution (movement) are performed. Based on the obtained results, it is found that the analyzed tundish is not of optimal design, in terms of removing small NMIs, as they are conducted in a stream of liquid flowing at the bottom of the tundish, moving directly into nozzles of the tundish. Their movement is caused by the shaped liquid‐flow phenomena in the tundish working space. The test results help to validate a numerical model, which can be used in further studies to redesign the working space of the tundish. The positive result of verification facilitates to obtain a tool for implementing flow optimization in terms of receiving high metallurgical purity of slabs.

The paper is dedicated to the verification of solidification of continuously cast round steel billets using numerical modelling based on the finite element method. The aim of numerical modelling is to optimize the production of continuously cast steel billets of round format. The paper describes the pre-processing, processing and post-processing phases of numerical modelling. Also, the problems with determination of the thermodynamic properties of materials and the heat transfer between the individual parts of the casting system, including the definition of the heat losses along the casting strand in the primary and secondary cooling, were discussed. The first results of numerical simulation show the so-called thermal steady state of continuous casting. The temperature field, the metallurgical length and the thickness of the shell at the end of the mould were predicted. The further research will be concentrated on the prediction the risk of the cracks and the porosity based on the different boundary conditions.

This paper deals with the possibilities of using physical modelling to study the slag entrainment in the tundish. A level of steel in the tundish is changing during sequential continuous casting. The most significant decrease in the steel level occurs when replacing ladles. It is generally known that if the height of steel level in the tundish drops below a certain critical level, it may generate vortexes over the nozzles and as a consequence entrainment of tundish slag into individual casting strands can occur. Thus, it is necessary to identify the critical level of steel for specific operational conditions. In this paper, the development of physical modelling methodology is described as well as physical model corresponding to operational continuous casting machine No. 2 in Třinecké železárny, a.s. The obtained results are discussed.