The air entrapment mechanisms in die-casting injection chambers that may produce porosity in manufactured parts are analyzed in this work using visualization techniques of the flow in a transparent injection chamber model, using water as working fluid. In particular, results for the free-surface profile evolution and for the volume of air remaining in the chamber at the instant at which the water begins to flow through the runner are analyzed for different maximum plunger speeds and initial filling fractions. A comparison between these visualizations and the numerical results of Zamora et al. (2007, “Experimental Verification of Numerical Predictions for the Optimum Plunger Speed in the Slow-Phase of a High-Pressure Die Casting Machine,” Int. J. Adv. Manuf. Technol., 33, pp. 266–276) which were obtained using a three-dimensional numerical model, shows a good degree of agreement. After discussing the air entrapment mechanisms that may produce porosity in manufactured parts, different experiments, which were carried out under real operating conditions using an aluminum alloy in a high-pressure die-casting machine with horizontal cold chamber, will be presented. The die-cavity geometry used in the experiments was appropriately modified to isolate the slow shot phase from the rest of the injection process, and the porosity levels in the manufactured parts were measured using a gravimetric technique. The optimum values of the maximum plunger speed that minimizes porosity in the manufactured parts have been determined. These values are very close to the previous numerical predictions of López et al. (2003, “On the Critical Plunger Speed and Three-Dimensional Effects in High-Pressure Die Casting Injection Chambers,” ASME J. Manuf. Sci. Eng., 125, pp. 529–537)
One of the most important problems encountered in die-casting processes is porosity due to air entrapment in the molten metal during the injection process. The aim of this work is to study experimentally and numerically the different air entrapment phenomena that may take place in the early stages of the filling of a vertical die cavity with a rectangular shape for operating conditions typically used in low and medium-pressure die-casting processes. Special attention is given to determining the influence of the gravitational forces on the flow pattern. Numerical simulation of the flow in the die cavity is carried out for the liquid phase using a commercial computational fluid dynamics (CFD) code (FLOW-3D) based on the solution algorithm-volume of fluid (SOLA-VOF) approach to solve the coupling between the momentum and mass conservation equations and to treat the free-surface, while the amount of air evacuated through vents is calculated by using an unsteady one-dimensional adiabatic model that retains friction effects. The main characteristics of the flow at the early instants of the die cavity filling are analyzed for different operating conditions, and the different flow patterns are summarized in a map as a function of the Reynolds and Froude numbers. Also, filling visualization experiments are carried out on a test bench using water as working fluid in a transparent die model and a high-speed camera. The numerical and experimental results obtained for the free-surface profile evolution are compared for different inlet velocities of the fluid and the viability of the numerical tools used to predict the final amount of trapped air in the die cavity is discussed.
The rear wall of the header box serves as a tubesheet in heat exchangers of double plate header box. Tube-to-tubesheet welding must be performed using orbital Gas Tungsten Arc Welding (GTAW) with a head extension, which is passed through the corresponding hole in the front wall (plugsheet) of the header box, where the welding machine is supported. In this project, the effect of parallelism deviations between the plugsheet and the tubesheet of carbon steel header box is analyzed to evaluate its influence on the quality of the tube-to-tubesheet welding. Welded tube (SA-210 Gr. A1) to tubesheet (SA-516 Gr. 70) coupons are manufactured simulating the parallelism deviations previously analyzed in two double plate header boxes of air-cooled heat exchangers using two different preheating temperatures. Macrographic analysis is performed in order to evaluate the weld penetration (minimum leak path) and length of the weld leg in tube-to-tubesheet joints. The results obtained show important variations in those parameters when the parallelism deviations are equal to or greater than −1 mm over the theoretical distance as well as when the distance approaches +1 mm or more. Finally, the incorporation of dimensional controls prior to the welding process is discussed and the implementation of improvements in orbital GTAW equipment is recommended as an optimal solution for this kind of heat exchangers.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.