Background Guided endodontics technique has been introduced for years, but the accuracy in different types of teeth has yet to be assessed. The aim of this study is to evaluate the accuracy of three dimensional (3D)-printed endodontic guides for access cavity preparation in different types of teeth, and to evaluate the predictive ability of angular and linear deviation on canal accessibility ex vivo. Method Eighty-four extracted human teeth were mounted into six jaw models and categorised into three groups: anterior teeth (AT), premolar (P), and molar (M). Preoperative cone beam computed tomography (CBCT) and surface scans were taken and matched using implant planning software. Virtual access cavity planning was performed, and templates were produced using a 3D printer. After access cavities were performed, the canal accessibility was recorded. Postoperative CBCT scans were superimposed in software. Coronal and apical linear deviations and angular deviations were measured and evaluated with nonparametric statistics. The receiver operating characteristic (ROC) curve was used to evaluate the predictive ability of angular and linear deviation for canal accessibility in SPSS v20. Results A total of 117 guided access cavities were created and 23 of them were record as canal inaccessibility, but all canals were accessible after canal negotiation. The average linear deviation for all groups was 0.13 ± 0.21 mm at coronal position, 0.46 ± 0.4 mm at apical position, and 2.8 ± 2.6° in angular deviation. At the coronal position, the linear deviations of the AT and P groups were significantly lower than M group deviation (P < 0.05), but no statistically significant difference between AT group and P group. The same results were found in linear deviation at the apical position and in angular deviation. The area under the ROC curve was 0.975 in angular deviation, 0.562 in linear deviation at the coronal position, and 0.786 at the apical position. Statistical significance was noted in linear deviation at the apical position and in angular deviation (P < 0.001). Conclusions In conclusion, this study demonstrated that the accuracy of access cavity preparation with 3D-printed endodontic guides was acceptable. The linear and angular deviations in the M group were significantly higher than those in the other groups, which might be caused by the interference of the opposite teeth. Angular deviation best discriminated the canal access ability of guided access cavity preparation. Graphical Abstract
This study aimed to review the literature on adult mandibular lingula (ML) locations and related distances determined using cone-beam computed tomography (CBCT). A search was conducted for studies on CBCT using the following databases: PubMed, Web of Science, and Embase. The search results were limited to studies published between 1970 and 2021. The inclusion criteria were the investigation of ML location, CBCT, and participants aged ≥18 years. Eligible studies were examined for the distances from the lingual tip to the anterior ramus border, posterior ramus border, sigmoid notch, inferior ramus border, and occlusal plane. Eight studies on CBCT qualified for inclusion in the study. The mean distances from the ML to the anterior ramus border were 15.57 to 20 mm. In most of these, the ML was located above the occlusal plane. No significant differences were observed in the location and related distances for the ML among patients of different sexes, ethnicities, or skeletal patterns.
The patterns of the lingula and antilingula are crucial surgical reference points for ramus osteotomy. Cone-beam computed tomography (CBCT) provides three-dimensional images, and patient radiation dose is significantly lower for CBCT than for medical CT. The morphology of the mandibular lingula and antilingula of ninety patients (180 sides) were investigated using CBCT. The lingula were classified as having triangular, truncated, nodular, and assimilated shapes. The antilingula were classified as having hill, ridge, plateau, and plain shapes. The patients’ sex, skeletal patterns (Classes I, II, and III), and right and left sides were recorded. The most to least common lingula shapes were nodular (37.8%), followed by truncated (32.8%), triangular (24.4%), and assimilated (5%). The most to least common antilingulae were hill (62.8%), plain (18.9%), plateau (13.9%), and ridge (4.4%) patterns, respectively. The lingula and antilingula had identical patterns on both sides in 47 (52.2%) and 46 patients (51.1%), respectively. Sex and skeletal pattern were not significantly correlated to lingula and antilingula shapes. No significant correlation was observed between lingula and antilingula shapes.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.