No abstract

Three-dimensional time-dependent quantum mechanical method has been used to study the influence of orientation, rotation, and vibration on the dissociation of water molecule on Cu(111) surface, using London-Eyring-Polanyi-Sato potential energy surface. Our calculations show that dependency of dissociation probability on the initial orientation of the molecule changes with the vibrational state of the molecule. It has also been found that for v(0) = 0 and 1, where v(0) stands for the vibrational state of the pseudo diatomic HO-H, the rotational excitation of the molecule increases the reactivity, whereas for v(0) = 2, the rotational excitation of the molecule decreases the reactivity. Vibrational excitation of the molecule greatly enhances the dissociation probability.

Water adsorption and dissociation on Ni(100) and Ni(111) surfaces are studied using density functional theory calculations. Water adsorbs on top site on both the surfaces, while H and OH adsorb on four fold hollow and three fold hollow (fcc) sites on Ni(100) and Ni(111), respectively. Transition states (TS) on both surfaces are identified using climbing image-nudged elastic band method. It is found that the barrier to dissociation on Ni(100) surface is slightly lower than that on Ni(111) surface. Dissociation on both the surfaces is exothermic, while the exothermicity on Ni(100) is large. To study the effect of lattice motion on the energy barrier, TS calculations are performed for various values of Q (lattice atom coordinate along the surface normal) and the change in the barrier height and position is determined. Calculations show that the energy barrier to reaction decreases with increasing Q and increases with decreasing Q on both the surfaces. Dissociation probability values at different surface temperatures are computed using semi-classical approximation. Results show that the influence of surface temperature on dissociation probability on the Ni(100) is significantly larger compared to that of Ni(111). Moreover, on Ni(100), a dramatic shift in energy barrier to lower incident energy values is observed with increasing surface temperature, while the shift is smaller in the case of Ni(111).

A comparative study of mode-selectivity of water dissociation on Ni(100), Ni(110), and Ni(111) surfaces is performed at the same level of theory using a fully quantum approach based on the reaction path Hamiltonian. Calculations show that the barrier to water dissociation on the Ni(110) surface is significantly lower compared to its close-packed counterparts. Transition states for this reaction on all three surfaces involve the elongation of one of the O-H bonds. A significant decrease in the symmetric stretching and bending mode frequencies near the transition state is observed in all three cases and in the vibrational adiabatic approximation, excitation of these softened modes results in a significant enhancement in reactivity. Inclusion of non-adiabatic couplings between modes results in the asymmetric stretching mode showing a similar enhancement of reactivity as the symmetric stretching mode. Dissociation probabilities calculated at a surface temperature of 300 K showed higher reactivity at lower collision energies compared to that of the static surface case, underlining the importance of lattice motion in enhancing reactivity. Mode selective behavior is similar on all the surfaces. Molecules with one-quantum of vibrational excitation in the symmetric stretch, at lower energies (up to ∼0.45 eV), are more reactive on Ni(110) than the Ni(100) and Ni(111) surfaces. However, the dissociation probabilities approach saturation on all the surfaces at higher incident energy values. Overall, Ni(110) is found to be highly reactive toward water dissociation among the low-index nickel surfaces owing to a low reaction barrier resulting from the openness and corrugation of the surface. These results show that the mode-selective behavior does not vary with different crystal facets of Ni qualitatively, but there is a significant quantitative effect.

Electrodeposition of Co–W alloy coatings has been carried out with DC and PC using gluconate bath at different pH. These coatings are characterized for their structure, morphology and chemical composition by X‐ray diffraction, field emission scanning electron microscopy, differential scanning calorimetry and X‐ray photoelectron spectroscopy (XPS). Alloy coatings plated at pH8 are crystalline, whereas coatings electrodeposited at pH5 are nanocrystalline in nature. XPS studies have demonstrated that as‐deposited alloy plated at pH8 with DC contain only Co2+ and W6+ species, whereas that alloy plated at pH5 has significant amount of Co0 and W0 along with Co2+ and W6+ species. Again, Co2+ and W6+ are main species in all as‐deposited PC plated alloys in both pH. Co0 concentration increases upon successive sputtering of all alloy coatings. In contrast, mainly W6+ species is detected in the following layers of all alloys plated with PC. Alloys plated at pH5 show higher microhardness compared to their pH8 counterparts. Copyright © 2013 John Wiley & Sons, Ltd.