ObjectivesThe objective of this study was to evaluate the discolouration effects of artificial saliva, granule lemon juice, coffee (without sugar), coca cola, sour cherry juice, fresh carrot juice and red wine on resin-based composite materials that are commonly used in restorative dentistry.MethodsColour of four brands of resin composites (Filtek Z 250 (3M Espe), Filtek Supreme (3M Espe), Quadrant (Cavex), Charisma (Heraeus-Kulzer)) of A2 shade was measured after one day of immersion in eight different solutions. Colour measurements were obtained by using a XL-20 Trismus Colourimeter and colour differences (ΔE) were estimated. For statistical evaluation, analysis of variance (ANOVA), Dunnett and Tukey tests were used at a significance level of 0.05.ResultsFor the four restorative materials tested, the lowest ΔE values were observed in the artificial saliva, while ΔE values were the highest in red wine group. When comparing the four different restorative materials, Filtek Supreme exhibited the least colour changes whereas Filtek Z250 was the least colour-stable.ConclusionsDental resin composites and drinking solutions were significant factors that may affect the colour stability. After immersion for one day, all materials showed visible colour changes. The red wine solution exhibited more staining than others in three groups. Filtek Supreme showed significantly the least colour change due to its nano particle sizes.
The microhardness, surface roughness and wear resistance of different types of resin composites, polymerized by a Quartz Tungsten Halogen (QTH) or Light Emitting Diode (LED) light curing units (LCU) were evaluated in this in vitro study. Cylindrical blocks were prepared from composites (8 mm in diameter, and 2 mm in thickness) and polymerized by a LED or a QTH LCU. Vickers hardness was measured on the top and bottom surfaces of the specimens. Surface roughness was measured with a surface profilometer on the top of the specimens. For the wear test, specimens were tested in a conventional pin-on-disc tribology machine under 15 N loads. The statistical analyses were performed by one-way analysis of variance (ANOVA) and t-tests, including the Bonferroni correction. Nanocomposite material Clearfil Majesty Posterior showed the highest hardness values in all polymerization types at the top and bottom surfaces (p < 0.05). Microhybrid Clearfil APX and hybrid Quixfil composites demonstrated the greatest surface roughness. Wear resistance of Clearfil Majesty Posterior was found to be the highest among the other tested resin composites. The results indicated that Clearfil Majesty Posterior demonstrated higher microhardness, less surface roughness, and higher wear resistance when compared with the other tested materials for both polymerization types.
The purpose of the current study was to determine the similarities of maxillary and mandibular third molars with the other molar teeth. A total of 2016 extracted maxillary and mandibular permanent teeth were evaluated. The teeth were divided into six groups. The teeth were stored in 5% nitric acid solution for 7 days, then placed in increasing concentrations of ethyl alcohol. The teeth were rendered transparent by immersion in xylene solution for 4 days until complete transparency was achieved. Three roots were present in 93.0% of the maxillary molars, and 91.3% of the second molars. Among the maxillary third molars, 35.5% were single-rooted and 24.9% of the mandibular third molars had single roots. Double roots were present in 69.2% of the mandibular third molars, and 5.4% had three roots. Four new root canal configurations were encountered in this study. The root canal configurations of the mandibular and maxillary teeth showed similarities with the results of other studies performed in different populations.
The aim of this study was to evaluate the regional push-out bond strengths for two fiber-reinforced post types using three different dentin bonding agents. Sixty single-rooted extracted human first premolar teeth were sectioned below the cemento-enamel junction, and the roots were endodontically treated. Following standardized post space preparations, the roots were divided into two fiber-post groups (Glassix and Carbopost), and further divided into three subgroups of 10 specimens each for the bonding systems self-etching dentin bonding agents (Clearfil SE Bond and Optibond all-in-one), and total-etching dentin bonding agent (XP Bond). A dual-cure resin luting cement (Maxcem) was then placed in the post spaces and posts were then seated into the root canals polymerized through the cervical portion. The roots were then cut into 3-mm thick sections. Push-out tests were performed at a crosshead speed of 0.5 mm/min. The data were analyzed with multivariate ANOVA (alpha = 0.05). The morphology of interface between different dentin bonding agents from the cervical sections were analyzed with SEM. Glass fiber-reinforced posts demonstrated significantly higher push-out bond strengths than carbon fiber-reinforced posts (p < 0.001). Bond strength values decreased significantly from the cervical to the apical root canal regions (p < 0.001). Self-etching dentin adhesive Clearfil SE Bond and total-etching dentin adhesive XP Bond demonstrated similar bond strengths values and this was significantly higher compared with the Optibond all-in-one in cervical root canal region. In conclusion, in all root segments, the glass fiber-reinforced posts provided significantly increased post retention than the carbon fiber-reinforced posts, regardless of the adhesive used.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.