The amount of liquid water in snow characterizes the wetness of a snowpack. Its temporal evolution plays an important role for wet-snow avalanche prediction, as well as the onset of meltwater release and water availability estimations within a river basin. However, it is still a challenge and a not yet satisfyingly solved issue to measure the liquid water content (LWC) in snow with conventional in situ and remote sensing techniques. We propose a new approach based on the attenuation of microwave radiation in the L-band emitted by the satellites of the Global Positioning System (GPS). For this purpose, we performed a continuous low-cost GPS measurement experiment at the Weissfluhjoch test site in Switzerland, during the snow melt period in 2013. As a measure of signal strength, we analyzed the carrier-to-noise power density ratio (C/N0) and developed a procedure to normalize these data. The bulk volumetric LWC was determined based on assumptions for attenuation, reflection and refraction of radiation in wet snow. The onset of melt, as well as daily melt-freeze cycles were clearly detected. The temporal evolution of the LWC was closely related to the meteorological and snow-hydrological data. Due to its non-destructive setup, its cost-efficiency and global availability, this approach has the potential to be implemented in distributed sensor networks for avalanche prediction or basin-wide melt onset measurements.

For numerous hydrological applications, information on snow water equivalent (SWE) and snow liquid water content (LWC) are fundamental. In situ data are much needed for the validation of model and remote sensing products; however, they are often scarce, invasive, expensive, or labor‐intense. We developed a novel nondestructive approach based on Global Positioning System (GPS) signals to derive SWE, snow height (HS), and LWC simultaneously using one sensor setup only. We installed two low‐cost GPS sensors at the high‐alpine site Weissfluhjoch (Switzerland) and processed data for three entire winter seasons between October 2015 and July 2018. One antenna was mounted on a pole, being permanently snow‐free; the other one was placed on the ground and hence seasonally covered by snow. While SWE can be derived by exploiting GPS carrier phases for dry‐snow conditions, the GPS signals are increasingly delayed and attenuated under wet snow. Therefore, we combined carrier phase and signal strength information, dielectric models, and simple snow densification approaches to jointly derive SWE, HS, and LWC. The agreement with the validation measurements was very good, even for large values of SWE (>1,000 mm) and HS (> 3 m). Regarding SWE, the agreement (root‐mean‐square error (RMSE); coefficient of determination (R2)) for dry snow (41 mm; 0.99) was very high and slightly better than for wet snow (73 mm; 0.93). Regarding HS, the agreement was even better and almost equally good for dry (0.13 m; 0.98) and wet snow (0.14 m; 0.95). The approach presented is suited to establish sensor networks that may improve the spatial and temporal resolution of snow data in remote areas.

Monitoring seasonal snow cover properties is critical for properly managing natural hazards such as snow avalanches or snowmelt floods. However, measurements often cannot be conducted in difficult terrain or lack the high temporal resolution needed to account for rapid changes in the snowpack, e.g., liquid water content (LWC). To monitor essential snowpack properties, we installed an upward looking ground‐penetrating radar (upGPR) and a low‐cost GPS system below the snow cover and observed in parallel its evolution during two winter seasons. Applying external snow height (HS) information, both systems provided consistent LWC estimates in snow, based on independent approaches, namely measurements of travel time and attenuation of electromagnetic waves. By combining upGPR and GPS, we now obtain a self‐contained approach instead of having to rely on external information such as HS. This allows for the first time determining LWC, HS, and snow water equivalent (SWE) nondestructively and continuously potentially also in avalanche‐prone slopes.

Snow water equivalent (SWE) is a key variable for various hydrological applications. It is defined as the depth of water that would result upon complete melting of a mass of snow. However, until now, continuous measurements of the SWE are either scarce, expensive, labor-intense, or lack temporal or spatial resolution especially in mountainous and remote regions. We derive the SWE for dry-snow conditions using carrier phase measurements from the Global Navigation Satellite System (GNSS) receivers. Two static GNSS receivers are used, whereby one antenna is placed below the snow and the other antenna is placed above the snow. The carrier phase measurements of both receivers are combined in double differences (DDs) to eliminate clock offsets and phase biases and to mitigate atmospheric errors. Each DD carrier phase measurement depends on the relative position between both antennas, an integer ambiguity due to the periodic nature of the carrier phase signal, and the SWE projected into the direction of incidence. The relative positions of the antennas are determined under snow-free conditions with millimeter accuracy using real-time kinematic positioning. Subsequently, the SWE and carrier phase integer ambiguities are jointly estimated with an integer least-squares estimator. We tested our method at an Alpine test site in Switzerland during the dry-snow season 2015-2016. The SWE derived solely by the GNSS shows very high correlation with conventionally measured snow pillow (root mean square error: 11 mm) and manual snow pit data. This method can be applied to dense low-cost GNSS receiver networks to improve the spatial and temporal information on snow.