Photodetectors based on three dimensional organic–inorganic lead halide perovskites have recently received significant attention. As a new type of light-harvesting materials, formamidinium lead iodide (FAPbI3) is known to possess excellent optoelectronic properties even exceeding those of methylammonium lead iodide (MAPbI3). To date, only a few photoconductor-type photodetectors based on FAPbI3 single crystals and polycrystalline thin films in a lateral structure have been reported. Here, we demonstrate low-voltage, high-overall-performance photodiode-type photodetectors in a sandwiched geometry based on polycrystalline α-FAPbI3 thin films synthesized by a one-step solution processing method and post-annealing treatment. The photodetectors exhibit a broadband response from the near-ultraviolet to the near-infrared (330–800 nm), achieving a high on/off current ratio of 8.6 × 104 and fast response times of 7.2/19.5 μs. The devices yield a photoresponsivity of 0.95 AW−1 and a high specific detectivity of 2.8 × 1012 Jones with an external quantum efficiency (EQE) approaching 182% at −1.0 V under 650 nm illumination. The photodiode-type photodetectors based on polycrystalline α-FAPbI3 thin films with superior performance consequently show great promise for future optoelectronic device applications.

High-performance bottom-gate 2D-layered (PEA)2SnI4 field-effect transistors have been fabricated using PVA/CL-PVP as gate dielectric layers.

The performance of perovskite solar cells is greatly affected by the crystallization of the perovskite active layer. Perovskite crystal grains should neatly arrange and penetrate the entire active layer for an ideal perovskite crystallization. These kinds of crystallized perovskite films exhibit fewer defects and longer carrier lifetime, which is beneficial to enhance the performance of perovskite solar cells. Here, by testing the residual charge of perovskite solar cells with different crystallization conditions, it is demonstrated that the residual charge exists widely at the grain boundary, which is parallel to the device, and the residual charge is related to the performance of the perovskite solar cells. Single crystal grains neatly arranged and penetrate the entire active layer can generate less residual charge and improve device performance of the perovskite solar cells. The results also show that the long decay time of open-circuit voltage comes from the detrapping of trapped carriers. The residual charge testing technology provides a new idea for the investigation of carrier trap and detrap characteristics in photovoltaic devices.

Lithium‐ion batteries (LIBs) have been widely applied in portable electronics (laptops, mobile phones, etc.) as one of the most popular energy storage devices. Currently, much effort has been devoted to exploring alternative high‐capacity anode materials and thus potentially constructing high‐performance LIBs with higher energy/power density. Here, high‐capacity anode nanomaterials based on the diverse types of mechanisms, intercalation/deintercalation mechanism, alloying/dealloying reactions, conversion reaction, and Li metal reaction, are reviewed. Moreover, recent studies in atomic‐scale storage mechanism by utilizing advanced microscopic techniques, such as in situ high‐resolution transmission electron microscopy and other techniques (e.g., spherical aberration‐corrected scanning transmission electron microscopy, cryoelectron microscopy, and 3D imaging techniques), are highlighted. With the in‐depth understanding on the atomic‐scale ion storage/release mechanisms, more guidance is given to researchers for further design and optimization of anode nanomaterials. Finally, some possible challenges and promising future directions for enhancing LIBs' capacity are provided along with the authors personal viewpoints in this research field.

A one-step colloidal process was adopted to prepare face-centered-cubic PbS nanocrystals with different shapes such as octahedral, starlike, cubic, truncated octahedral, and truncated cubic. The features of this approach avoid the presynthesis of any organometallic precursor and the injection of a toxic phosphine agent. A layered intermediate compound (lead thiolate) forms in the initial stage of the reaction, which effectively acts as the precursor to decompose into the PbS nanocrystals. The size and shape of the PbS nanocrystals can be easily controlled by varying the reaction time, the reactant concentrations, the reaction temperatures, and the amount of surfactants. In particular, additional surfactants other than dodecanethiol, such as oleylamine, oleic acid, and octadecene, play an important role in the shape control of the products. The possible formation mechanism for the PbS nanocrystals with various shapes is presented on the basis of the different growth directions of the nanocrystals with the assistance of the different surfactants. This method provides a facile, low-cost, highly reproducible process for the synthesis of PbS nanocrystals that may have potential applications in the fabrication of photovoltaic devices and photodetectors.