Graphene adalah material baru yang ditemukan tahun 2004 secara sederhana oleh Andre Geim dan Konstantin Novoselov dengan menggunakan selotip yang direkatkan dengan karbon sehingga didapat lapisan dengan orde nanometer dari karbon tersebut. Graphene memiliki keunggulan mobilitas muatan yang tinggi dan memiliki konduktivitas listrik dan panas lebih baik dari material yang lain. Terutama dalam pembuatan super kapasitor yang dapat menyimpan muatan listrik. Penelitian ini Bertujuan untuk merancang superkapasitor dengan bahan dari graphene, activated carbon, polyurethane dan phosporic acid (H3PO4) dan menganalisi muatan listrik dan tegangan yang tersimpan selama pengecasan berlangsung, pada percobaan pertama pengecasan selama 1 menit dengan tegangan yang tersimpan 1,8volt dan tegangan akan habis selama 50:20,2 menit, maka voltase yang turun setiap detiknya 0.0006 v/s pada percobaan ke dua pengecasan selama 2 menit dengan tegangan yang tersimpan 1,8volt dan tegangan akan habis selama 58:28,8 menit, maka voltase yang turun setiap detiknya 0.0005 v/s pada percobaan ketiga pengecasan selama 60:24 menit dengan tegangan yang tersimpan 2volt dan tegangan akan habis selama 180:18,4 menit, maka voltase yang turun setiap detiknya 0.000185 v/s penelitian tersebut dapat disimpulkan bahwa superkapasitor memiliki muatan tegangan yang kecil tetapi memiliki daya simpan yang lama.
Jumlah sampah yang berlebihan dapat diatasi dengan cara daur ulang. Sebelum melakukan daur ulang, limbah harus disortir terlebih dahulu. Pemilahan sampah secara otomatis dalam jumlah besar dapat dilakukan dengan menggunakan sensor infra merah, sensor logam, dan sensor cahaya. Hasil pengujian menunjukkan bahwa pemilahan sampah otomatis dapat memilah sampah sesuai jenisnya. Namun masih ada kesalahan berupa limbah yang macet dan deteksi kesalahan oleh sensor.
Penyaluran tenaga listrik baik dari Pembangkit sampai ke Gardu induk sampai ke konsumen harus diperhatikan keandalan dan efisiensinya, agar tenaga listrik yang tersalurkan berkualitas dan memiliki kontinuitas yang baik. Guna menjaga kualitas tenaga listrik agar tetap andal dan efisien serta agar kontinuitas penyaluran tenaga listrik tetap terjaga dengan baik, beberapa komponen peralatan penyaluran tenaga listrik harus menjadi perhatian untuk mencegah terjadinya gangguan terhadap peralatan tenaga listrik. Salah satu gangguan pada peralatan tenaga listrik adalah titik panas (hot point). Seringnya terjadi gangguan tersebut pada titik pertemuan antara klem dan konduktor pada peralatan listrik menjadi tolak ukur pemeliharaan dalam penyediaan tenaga listrik. Tindakan pencegahan agar tidak terjadinya hot point disebut thermovisi, dengan menggunakan alat ukur thermal imagers. Prinsip kerja thermal imagersadalah merefleksikan cahaya infrared terhadap peralatan kemudian menangkap suhu peralatan tersebut dan menampilkannya pada sebuah display. Kegiatan thermovisi dilakukan secara rutin sebagai kegiatan monitoring pemeliharaan tenaga listrik yang kemudian dilakukan analisa hasil thermovisi tersebut dengan melakukan perhitungan emisivitas melalui pendekatan selisih suhu klem dan konduktor (∆T) agar didapatkan nilai emisivitas yang sesuai.Selanjutnya dilakukan uji validasi untuk menguji keakuratan dan presisi dari hasil thermovisi tersebut.Penelitian yang dilakukan di GI 150 kV Glugur bertujuan untuk merekomendasikan hasil uji analisa matematis terhadap tindak lanjut kondisi peralatan. Hasil dari kondisi peralatan pada analisa 30 sampel menunjukan bahwa peralatan masih dalam kondisi baik dan masih layak digunakan, dengan nilai akurasi sebesar 98,02% dan presisi sebesar 0,25% pada peralatan bay penghantar Glugur - Paya Geli 1 serta nilai akurasi pada bay penghantar Glugur – Paya Geli 2 sebesar 97,9% dan 0,24% pada nilai presisinya.
The sun shines on the territory of Indonesia for about 10 to 12 hours every day, so that solar power plants can be developed in Indonesia, the government has launched the movement of one million PLTS roofs in 2017, this research uses solar panels with a capacity of 200 Wp, which consists of 2 solar panels connected in parallel, solar charge controllers, batteries, inverters and as an AC load a fan, soldering iron and LED lights, the research aims to determine the output current, voltage and output power of the inverter when given an alternating current load that is inductive, resistive and capacitive, the method used is to measure the intensity of the sun, temperature, voltage, electric current, power factor, when the load is large the voltage drops depending on the given load, the inductive fan load has a voltage drop that is greater than the voltage drop that occurs in the soldering load and the LED lamp, the large current flowing on the output side fan load wants to be bigger than output current flowing in the solder and LED lights, the low efficiency of the inverter used can shorten the life of the electrical equipment used.
Many automatic machines implemented in the processing of palm oil in the industry are less effective in working on a heating control process in the jacket water system. With the ATMega, 328 Arduino Uno microcontroller control system as an Arduino program input and output controller and “C” language, a servo motor as output (valve) is controlled, and LCD as a display device for LM35 temperature detection can make it easier for workers to control the process of controlling water temperature on the jacket and can avoid failure in the process of melting the palm oil from the previous processing so that the oil in the pipeline continues to flow. The method used in this research is the design method that consists of several stages, namely, (1) Requirement analysis, (2) Design, (3) Implementation of the circuit, (4) Testing Procedures and (5) Testing tools. The level of accuracy of the rotation degree of the servo motor (as a valve) qualifies 100% (>35 °C and ≤ 49 °C, the motor rotates 40o), the relationship between temperature and the rotation speed of the servo motor qualifies with 100% accuracy (>50 °C and ≤ 53 °C then the motor rotates 80 °C) The overall performance of this tool can work well and calibration of the detection temperature value between the LM35 sensor with a thermometer has a difference of 1 mV so that it can be implemented by adjusting devices in the industry.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.