An experimental study has been made of the flow field in indentation of a model granular material. A granular ensemble composed of spherical sand particles with average size of 0.4 mm is indented with a flat ended punch under plane-strain conditions. The region around the indenter is imaged in situ using a high-speed charge-coupled device (CCD) imaging system. By applying a hybrid image analysis technique to image sequences of the indentation, flow parameters such as velocity, velocity gradient, and strain rate are measured at high resolution. The measurements have enabled characterization of the main features of the flow such as dead material zones, velocity jumps, localization of deformation, and regions of highly rotational flow resembling vortices. Implications for validation of theoretical analyses and applications are discussed.

Here, we detail and analyse a multi-resolution particle image velocity measurement that resolves the wide range of scales prevalent in a zero pressure gradient turbulent boundary layer at high Reynolds numbers (up to Reτ ≈ 20 000). A unique configuration is utilised, where an array of eight high resolution cameras at two magnification levels are used simultaneously to obtain a large field of view, while still resolving the smaller scales prevalent in the flow. Additionally, a highly magnified field of view targeted at the near wall region is employed to capture the viscous sublayer and logarithmic region, with a spatial resolution of a few viscous length scales. Flow statistics from these measurements show good agreement with prior, well resolved hot-wire anemometry measurements. Analysis shows that the instantaneous wall shear stress can be reliably computed, which is historically known to be challenging in boundary layers. A statistical assessment of the wall shear stress shows good agreement with existing correlations, prior experimental and direct numerical simulation data, extending this view to much higher Reynolds numbers. Furthermore, conditional analysis using multiple magnification levels is detailed, to study near-wall events associated with high skin friction fluctuations and their associated overlaying structures in the log region. Results definitively show that the passage of very large-scale positive (or negative) velocity fluctuations are associated with increased (or reduced) small-scale variance in wall shear stress fluctuations.

The plane wall jet (PWJ) is a wall-bounded flow in which a wall shear layer develops in the presence of extremely energetic flow structures of the outer free-shear layer. The structure of a PWJ, developing in still air, was studied with the focus on the large scales in the flow. Wall-normal hot-wire anemometry (HWA) measurements along with double-frame particle image velocimetry (PIV) measurements (wall-normal–streamwise plane) were carried out at streamwise distances up to $162b$, where $b$ is the slot width of the PWJ exit. The nominal PWJ Reynolds number based on exit parameters was $Re_{j}\approx 5940$. Comparisons with a zero-pressure-gradient boundary layer (ZPGBL) at nominally matched friction Reynolds number $Re_{\unicode[STIX]{x1D70F}}$ were also carried out as appropriate, to highlight key features of the PWJ structure. Consistent with previous work, the PWJ showed a dependence of the peak turbulent stresses on the jet exit Reynolds number. The turbulent production showed a peak corresponding to the near-wall cycle similar to the peak seen in the ZPGBL. However, another turbulent production peak was observed in the outer free-shear layer that was an order of magnitude larger than the inner one. Along with the change in sign of the viscous and Reynolds shear stresses, the PWJ was shown to have a region of very low turbulent production between these two peaks. The dissipation rate increased over the PWJ layer with a peak also in the outer region. Visualizations of the flow and two-point correlations reveal that the most energetic large-scale structures within a PWJ are vortical motions in the wall-normal–streamwise plane similar to those structures seen in free-shear layers. These structures are referred to as J (for jet) type structures. In addition two-point correlations reveal the existence of large-scale structures in the wall region which have a signature similar to those structures seen in canonical boundary layers. These structures are referred to as W (for wall) type structures. Instantaneous PIV realizations and flow visualizations reveal that these W type large-scale features are consistent with the paradigm of hairpin vortex packets in the wall region. The J type structures were seen to intrude well into the wall region while the W type structures were also seen to extend into the outer shear layer. Further, these large-scale structures were shown to modulate the amplitude of the finer scales of the flow.

A hybrid particle image velocimetry/particle tracking velocimetry (PIV/PTV) method is described for direct measurement of large-strain deformation fields using plane-strain machining as the model system. PIV/PTV is shown to accurately measure displacements and velocities with a spatial resolution of ∼1/10th of a pixel, which is an order of magnitude improvement over a comparable PIV-based method. For the configuration studied here, this translates to about ∼400 nm in terms of displacement and ∼80 µm s−1 in terms of velocity. Furthermore, the method is shown to be able to capture steep gradients in velocity, which are typical of deformation zones in machining. This enables accurate estimation of associated strain rates. Implications of the technique for measuring large-strain fields in deformation processes and indentation tests, and velocity gradients due to friction at sliding interfaces, are briefly discussed.