The tip clearance flows of transonic compressor rotors are important because they have a significant impact on rotor and stage performance. While numerical simulations of these flows are quite sophisticated, they are seldom verified through rigorous comparisons of numerical and measured data because these kinds of measurements are rare in the detail necessary to be useful in high-speed machines. In this paper we compare measured tip-clearance flow details (e.g. trajectory and radial extent) with corresponding data obtained from a numerical simulation. Recommendations for achieving accurate numerical simulation of tip clearance flows are presented based on this comparison. Laser Doppler Velocimeter (LDV) measurements acquired in a transonic compressor rotor, NASA Rotor 35, are used. The tip clearance flow field of this transonic rotor was simulated using a Navier-Stokes turbomachinery solver that incorporates an advanced k-ε turbulence model derived for flows that are not in local equilibrium. Comparison between measured and simulated results indicates that simulation accuracy is primarily dependent upon the ability of the numerical code to resolve important details of a wall-bounded shear layer formed by the relative motion between the over-tip leakage flow and the shroud wall. A simple method is presented for determining the strength of this shear layer.

The tip clearance flows of transonic compressor rotors are important because they have a significant impact on rotor and stage performance. A wall-bounded shear layer formed by the relative motion between the overtip leakage flow and the shroud wall is found to have a major influence on the development of the tip clearance flow field. This shear layer, which has not been recognized by earlier investigators, impacts the stable operating range of the rotor. Simulation accuracy is dependent on the ability of the numerical code to resolve this layer. While numerical simulations of these flows are quite sophisticated, they are seldom verified through rigorous comparisons of numerical and measured data because these kinds of measurements are rare in the detail necessary to be useful in high-speed machines. In this paper we compare measured tip-clearance flow details (e.g., trajectory and radial extent) with corresponding data obtained from a numerical simulation. Laser-Doppler Velocimeter (LDV) measurements acquired in a transonic compressor rotor, NASA Rotor 35, are used. The tip clearance flow field of this transonic rotor is simulated using a Navier–Stokes turbomachinery solver that incorporates an advanced k–ε turbulence model derived for flows that are not in local equilibrium. A simple method is presented for determining when the wall-bounded shear layer is an important component of the tip clearance flow field. [S0889-504X(00)02504-6]

Model scale tests of modern 'open rotor' propulsor concepts that have potential for significant fuel burn reduction for aircraft applications were completed at NASA Glenn Research Center. The recent test campaign was a collaboration between NASA, FAA, and General Electric (GE). GE was the primary industrial partner, but other organisations were involved such as Boeing and Airbus who provided additional hardware for fuselage simulations. The open rotor is a modern version of the UnDucted Fan (UDF ® ) that was flight tested in the late 1980s through a partnership between NASA and GE. The UDF ® was memorable for its scimitar shaped propeller blades and its unique noise signature. Design methods of the time were not able to optimise for both high aerodynamic efficiency and low noise simultaneously. Contemporary CFD/CAA based design methods can produce open rotor blade designs that maintain efficiency with acceptable acoustic signatures. Tests of two generations of new open rotor designs were conducted in the 9' × 15' Low Speed Wind Tunnel and the 8' × 6' Supersonic Wind Tunnel starting in late 2009 and completed in early 2012. Aerodynamic performance and acoustic data were obtained for take-off, approach and cruise conditions in isolated and semi-installed configurations. Additional detailed flow diagnostic measurements and acoustic

Rotor wakes are an important source of loss in axial compressors. The decay rate of a rotor wake is largely due to both mixing (results in loss) and stretching (no loss accrual). Thus, the actual loss associated with rotor wake decay will vary in proportion to the amounts of mixing and stretching involved. This wake stretching process, referred to by Smith (1996) as recovery, is reversible and for a 2-D rotor wake leads to an inviscid reduction of the velocity deficit of the wake. It will be shown that for the rotor/stator spacing typical of core compressors, wake stretching is the dominant wake decay process within the stator with viscous mixing playing only a secondary role. A model for the rotor wake decay process is developed and used to quantify the viscous dissipation effects relative to those of inviscid wake stretching. The model is verified using laser anemometer measurements acquired in the wake of a transonic rotor operated alone and in a stage configuration at near peak efficiency and near stall operating conditions. Results from the wake decay model exhibit good agreement with the experimental data. Data from the model and laser anemometer measurements indicate that rotor wake straining (stretching) is the primary decay process in the stator passage. Some implications of these results on compressor stage design are discussed.

The rising cost of jet fuel has renewed interest in contra-rotating open rotor propulsion systems. Contemporary design methods offer the potential to maintain the inherently high aerodynamic efficiency of open rotors while greatly reducing their noise output, something that was not feasible in the 1980’s designs. The primary source mechanisms of open rotor noise generation are thought to be the front rotor wake and tip vortex interacting with the aft rotor. In this paper, advanced measurement techniques and high-fidelity prediction tools are used to gain insight into the relative importance of the contributions to the open rotor noise signature of the front rotor wake and rotor tip vortex. The measurements include three-dimensional particle image velocimetry of the intra-rotor flowfield and the acoustic field of a model-scale open rotor. The predictions provide the unsteady flowfield and the associated acoustic field. The results suggest that while the front rotor tip vortex can have a significant influence on the blade passing tone noise produced by the aft rotor, the front rotor wake plays the decisive role in the generation of the interaction noise produced as a result of the unsteady aerodynamic interaction of the two rotors. At operating conditions typical of takeoff and landing operations, the interaction noise level is easily on par with that generated by the individual rotors, and in some cases is even higher. This suggests that a comprehensive approach to reducing open rotor noise should include techniques for mitigating the wake of the front rotor as well as eliminating the interaction of the front rotor tip vortex with the aft rotor blade tip.