Friction press joining is an innovative joining process for bonding plastics and metals without additives in an overlap configuration. A model-based approach for the design of an axial force controller for friction press joining is presented in this paper. A closed-loop control was set up on the machining center, in which the plunge depth was used as the controlling variable. In order to support the controller development, a nonparametric dynamic process model was developed via a data-based system identification. Subsequently, various control concepts were designed off-line and verified on the actual system. The most promising ones, a proportional controller, a controller created with the pole placement method, and a model predictive controller, were selected for further investigations. The three controllers were re-evaluated and compared by means of a defined input of disturbance variables and reference variables. The model predictive control (MPC) approach as well as the proportional controller were also tested for model uncertainties. For this purpose, different material combinations were joined using the different controllers. Thereby, it was shown that the MPC controller resulted in smaller standard deviations when encountering large model uncertainties. The investigations demonstrated the high potential of friction press joining of plastic components with metals. The results form the basis for future research, whereby the force can be specified as an additional input parameter instead of the plunge depth.
Coaxial Laser Metal Deposition with wire (LMD-w) is a valuable complement to the already established Additive Manufacturing processes in production because it allows a direction-independent process with high deposition rates and high deposition accuracy. However, there is a lack of knowledge regarding the adjustment of the process parameters during process development to build defect-free parts. Therefore, in this work, a process development for coaxial LMD-w was conducted using an aluminum wire AlMg4,5MnZr and a stainless steel wire AISI 316L. At first, the boundaries for parameter combinations that led to a defect-free process were identified. The proportion between the process parameters energy per unit length and speed ratio proved crucial for a defect-free process. Then, the influence of the process parameters on the height and width of single beads for both materials was analyzed using a regression analysis. It was shown that linear models are suitable for describing the correlation between the process parameters and the dimensions of the beads. Lastly, a material-independent formula is presented to calculate the height increment per layer needed for an additive process. For future studies, the results of this work will be an aid for process development with different materials.
Reactive particles consisting of nickel and aluminum represent an adaptable heat source for joining applications, since each individual particle is capable of undergoing a self-sustaining exothermic reaction. Of particular interest are particles with intrinsic lamellar microstructures, as they provide large contact areas between the reactants nickel and aluminum. In this work, the exothermic reaction as well as the microstructure of such lamellar reactive particles produced by high energy planetary ball milling were investigated. Based on statistically designed experiments regarding the milling parameters, the heat of reaction was examined by means of differential scanning calorimetry (DSC). A statistical model was derived from the results to predict the heat of reaction as a function of the milling parameters used. This model can be applied to adjust the heat of reaction of the reactive particles depending on the thermal properties of the joining partners. The fabricated microstructures were evaluated by means of scanning electron microscopy (SEM). Through the development of a dedicated SEM image evaluation algorithm, a computational quantification of the contact area between nickel and aluminum was enabled for the first time. A weak correlation between the contact area and the heat of reaction could be demonstrated. It is assumed that the quantification of the contact areas can be further improved by a higher number of SEM images per sample. The findings obtained provide an essential contribution to enable reactive particles as a tailored heat source for joining applications.
Coaxial laser metal deposition with wire (LMD-w) is an innovative additive manufacturing technology in which a wire is coaxially fed through the center of a hollow laser beam into a laser-induced melt pool. This special configuration results in a direction-independent process, which facilitates the manufacturing of thin-walled metal components at high deposition rates. However, laborious experimental test series must be conducted to adjust the process parameters so that the substrate and the part do not overheat. Therefore, models are needed to predict the resulting temperature field and melt pool dimensions efficiently. This paper proposes a finite element simulation model using an innovative heat source, which considers the unique intensity distribution of the annular laser spot. The heat source parameters were calibrated experimentally based on fusion lines obtained from metallographic cross sections of aluminum alloy samples (AA5078 wire and AA6082 substrate). Subsequently, the temperature distribution in the substrate plate was measured by means of thermocouples to validate the developed model. It was shown that the proposed heat source replicates the heat input accurately. With the presented model, essential features for process development, such as the temperature field and the melt pool dimensions, can be reliably predicted. The model contributes to a better understanding of the LMD-w process and facilitates an efficient process development in future research work as well as for industrial applications. Key words: thermal simulation, annular laser spot, heat source, laser metal deposition, coaxial wire feeding, directed energy deposition
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.