The biophysical determinants related to swimming performance are one of the most attractive topics within swimming science. The aim of this paper was to do an update of the "state of art" about the interplay between performance, energetic and biomechanics in competitive swimming. Throughout the manuscript some recent highlights are described: (i) the relationship between swimmer's segmental kinematics (segmental velocities, stroke length, stroke frequency, stroke index and coordination index) and his center of mass kinematics (swimming velocity and speed fluctuation); (ii) the relationships between energetic (energy expenditure and energy cost) and swimmer's kinematics; and (iii) the prediction of swimming performance derived from above mentioned parameters.

No abstract

Long-term function of three-dimensional (3D) tissue constructs depends on adequate vascularization after implantation. Accordingly, research in tissue engineering has focused on the analysis of angiogenesis. For this purpose, 2 sophisticated in vivo models (the chorioallantoic membrane and the dorsal skinfold chamber) have recently been introduced in tissue engineering research, allowing a more detailed analysis of angiogenic dysfunction and engraftment failure. To achieve vascularization of tissue constructs, several approaches are currently under investigation. These include the modification of biomaterial properties of scaffolds and the stimulation of blood vessel development and maturation by different growth factors using slow-release devices through pre-encapsulated microspheres. Moreover, new microvascular networks in tissue substitutes can be engineered by using endothelial cells and stem cells or by creating arteriovenous shunt loops. Nonetheless, the currently used techniques are not sufficient to induce the rapid vascularization necessary for an adequate cellular oxygen supply. Thus, future directions of research should focus on the creation of microvascular networks within 3D tissue constructs in vitro before implantation or by co-stimulation of angiogenesis and parenchymal cell proliferation to engineer the vascularized tissue substitute in situ.

Long-term function of three-dimensional (3D) tissue constructs depends on adequate vascularization after implantation. Accordingly, research in tissue engineering has focused on the analysis of angiogenesis. For this purpose, 2 sophisticated in vivo models (the chorioallantoic membrane and the dorsal skinfold chamber) have recently been introduced in tissue engineering research, allowing a more detailed analysis of angiogenic dysfunction and engraftment failure. To achieve vascularization of tissue constructs, several approaches are currently under investigation. These include the modification of biomaterial properties of scaffolds and the stimulation of blood vessel development and maturation by different growth factors using slow-release devices through pre-encapsulated microspheres. Moreover, new microvascular networks in tissue substitutes can be engineered by using endothelial cells and stem cells or by creating arteriovenous shunt loops. Nonetheless, the currently used techniques are not sufficient to induce the rapid vascularization necessary for an adequate cellular oxygen supply. Thus, future directions of research should focus on the creation of microvascular networks within 3D tissue constructs in vitro before implantation or by co-stimulation of angiogenesis and parenchymal cell proliferation to engineer the vascularized tissue substitute in situ.

Biofilm formation was evaluated on the following titanium and zirconia implants in vivo: machined titanium (Ti-m), modified titanium (TiUnite), modified zirconia (ZiUnite), machined alumina-toughened zirconia (ATZ-m), sandblasted alumina-toughened zirconia (ATZ-s), and machined zirconia (TZP-A-m). Bovine enamel slabs were used as controls. Surface morphologies were examined by atomic force (AFM) and scanning electron microscopy (SEM). The surface wettability was also determined. Twelve healthy volunteers wore a splint system with the tested materials. After 3 and 5 days the materials were examined by fluorescence in situ hybridization (FISH) and confocal laser scanning microscopy (CLSM). The levels of Streptococcus spp., Veillonella spp., Fusobacteriaum nucleatum, and Actinomyces naeslundii were quantitatively determined. The biofilm thickness was found to be between 19.78 and 36.73 μm after 3 days and between 26.11 and 32.43 μm after 5 days. With the exception of Ti-m the biofilm thickness after 3 days was correlated with surface roughness. In addition to Streptococcus spp. as the main component of the biofilm (11.23-25.30%), F. nucleatum, A. naeslundii, and Veillonella spp. were also detected. No significant differences in biofilm composition on the implant surfaces could be observed. In total, the influence of roughness and material on biofilm formation was compensated by biofilm maturation.