No abstract

This paper reports a novel composite-based processing route for improving the electrical performance of Ca3Co4O9 thermoelectric (TE) ceramics. The approach involves the addition of metallic Co, acting as a pore filler on oxidation, and considers two simple sintering schemes. The (1-x)Ca3Co4O9/xCo composites (x = 0%, 3%, 6% and 9% vol.) have been prepared through a modified Pechini method, followed by one- and two-stage sintering, to produce low-density (one-stage, 1ST) and high-density (two-stage, 2ST) ceramic samples. Their high-temperature TE properties, namely the electrical conductivity (σ), Seebeck coefficient (α) and power factor (PF), were investigated between 475 and 975 K, in air flow, and related to their respective phase composition, morphology and microstructure. For the 1ST case, the porous samples (56%–61% of ρth) reached maximum PF values of around 210 and 140 μWm−1·K−2 for the 3% and 6% vol. Co-added samples, respectively, being around two and 1.3 times higher than those of the pure Ca3Co4O9 matrix. Although 2ST sintering resulted in rather dense samples (80% of ρth), the efficiency of the proposed approach, in this case, was limited by the complex phase composition of the corresponding ceramics, impeding the electronic transport and resulting in an electrical performance below that measured for the Ca3Co4O9 matrix (224 μWm−1·K−2 at 975K).

The electrochemical reduction of iron oxides in alkaline media arises as a novel approach for ironmaking and iron-rich waste valorisation. Strong advantages and attractive aspects of alkaline electroreduction include lower electric energy consumption, absence of CO2 emissions, and non-polluting valuable by-products such as H2 and O2. Another potential advantage originates from the compatibility of this concept with intermittent renewable energies. However, to bring this technology to a competitive level, especially compared to the traditional steelmaking, innovative approaches and developments in materials processing and their appropriate integration into the electrolysis process are required. This research work explores the prospects for electrochemical reduction of a magnesium-containing ferrospinel, as a potential component in iron-containing wastes. The experimental approach considers bulk cathode- and suspension-based electrolysis concepts, which allow reaching 55% and 20% Faradaic efficiencies of the reduction to metallic iron, respectively. The effects imposed by the magnesium presence on the electroreduction kinetics, phase composition and morphology of the electroreduction products are evaluated and discussed. The obtained results open new perspectives for the recovery of metallurgical residues with low magnesium impurities content.

This work further explores the possibilities for designing the high-temperature electrical performance of the thermoelectric Ca3Co4O9 phase, by a composite approach involving separate metallic iron and nickel particles additions, and by employing two different sintering schemes, capable to promote the controlled interactions between the components, encouraged by our recent promising results obtained for similar cobalt additions. Iron and nickel were chosen because of their similarities with cobalt. The maximum power factor value of around 200 μWm−1K−2 at 925 K was achieved for the composite with the nominal nickel content of 3% vol., processed via the two-step sintering cycle, which provides the highest densification from this work. The effectiveness of the proposed approach was shown to be strongly dependent on the processing conditions and added amounts of metallic particles. Although the conventional one-step approach results in Fe- and Ni-containing composites with the major content of the thermoelectric Ca3Co4O9 phase, their electrical performance was found to be significantly lower than for the Co-containing analogue, due to the presence of less-conducting phases and excessive porosity. In contrast, the relatively high performance of the composite with a nominal nickel content of 3% vol. processed via a two-step approach is related to the specific microstructural features from this sample, including minimal porosity and the presence of the Ca2Co2O5 phase, which partially compensate the complete decomposition of the Ca3Co4O9 matrix. The obtained results demonstrate different pathways to tailor the phase composition of Ca3Co4O9-based materials, with a corresponding impact on the thermoelectric performance, and highlight the necessity of more controllable approaches for the phase composition tuning, including lower amounts and different morphologies of the dispersed metallic phases.

Oxide materials based on calcium manganite show clear prospects as thermoelectrics, provided by their stability at high temperatures and inherent flexibility in tuning the relevant electrical and thermal transport properties. Donor-doped CaMnO 3 is an n-type semiconductor with a perovskite structure and relatively high thermoelectric performance. In this work, the precursor powders have been modified through potassium carbonate additions to produce Ca 0.9 Gd 0.1-MnO 3 pellets without the usual delamination problems occurring during the compaction process. In order to demonstrate the relevant effects, several samples with different amounts of potassium carbonate (0-15 wt%) have been prepared. The results showed that potassium additions significantly facilitate the compaction procedure, while also improving the thermoelectric performances. The results also highlight the importance of porosity control for improving ZT, by decreasing the thermal conductivity without reduction of the electrical performance. The highest ZT values were observed for the samples processed at 15 wt% of potassium carbonate addition, exhibiting an improvement at least 30% at 800°C when compared to the pure samples.