Neural progenitor cell (NPC) culture within 3D hydrogels is an attractive strategy for expanding a therapeutically-relevant number of stem cells. However, relatively little is known about how 3D material properties such as stiffness and degradability affect the maintenance of NPC stemness in the absence of differentiation factors. Over a physiologically-relevant range of stiffness from ~0.5–50 kPa, stemness maintenance did not correlate with initial hydrogel stiffness. In contrast, hydrogel degradation was both correlated with, and necessary for, maintenance of NPC stemness. This requirement for degradation was independent of cytoskeletal tension generation and presentation of engineered adhesive ligands, instead relying on matrix remodeling to facilitate cadherin-mediated cell-cell contact and promote β-catenin signaling. In two additional hydrogel systems, permitting NPC-mediated matrix remodeling proved to be a generalizable strategy for stemness maintenance in 3D. Our findings have identified matrix remodeling, in the absence of cytoskeletal tension generation, as a previously unknown strategy to maintain stemness in 3D.

Cartilage lesions can progress into secondary osteoarthritis and cause severe clinical problems in numerous patients. As a prospective treatment of such lesions, human-derived induced pluripotent stem cells (iPSCs) were shown to be 3D bioprinted into cartilage mimics using a nanofibrillated cellulose (NFC) composite bioink when co-printed with irradiated human chondrocytes. Two bioinks were investigated: NFC with alginate (NFC/A) or hyaluronic acid (NFC/HA). Low proliferation and phenotypic changes away from pluripotency were seen in the case of NFC/HA. However, in the case of the 3D-bioprinted NFC/A (60/40, dry weight % ratio) constructs, pluripotency was initially maintained, and after five weeks, hyaline-like cartilaginous tissue with collagen type II expression and lacking tumorigenic Oct4 expression was observed in 3D -bioprinted NFC/A (60/40, dry weight % relation) constructs. Moreover, a marked increase in cell number within the cartilaginous tissue was detected by 2-photon fluorescence microscopy, indicating the importance of high cell densities in the pursuit of achieving good survival after printing. We conclude that NFC/A bioink is suitable for bioprinting iPSCs to support cartilage production in co-cultures with irradiated chondrocytes.

Better understanding of the fundamental mechanisms behind metabolic diseases requires methods to monitor lipid stores on single-cell level in vivo. We have used Caenorhabditis elegans as a model organism to demonstrate the limitations of fluorescence microscopy for imaging of lipids compared with coherent antiStokes Raman scattering (CARS) microscopy, the latter allowing chemically specific and label-free imaging in living organisms. CARS microscopy was used to quantitatively monitor the impact of genetic variations in metabolic pathways on lipid storage in 60 specimens of C. elegans. We found that the feeding-defective mutant pha-3 contained a lipid volume fraction one-third of that found in control worms. In contrast, mutants (daf-2, daf-4 dauer) with deficiencies in the insulin and transforming growth factors (IGF and TGF-␤) signaling pathways had lipid volume fractions that were 1.4 and 2 times larger than controls, respectively. This was observed as an accumulation of small-sized lipid droplets in the hypodermal cells, hosting as much as 40% of the total lipid volume in contrast to the 9% for the wild-type larvae. Spectral CARS microscopy measurements indicated that this is accompanied by a shift in the ordering of the lipids from gel to liquid phase. We conclude that the degree of hypodermal lipid storage and the lipid phase can be used as a marker of lipid metabolism shift. This study shows that CARS microscopy has the potential to become a sensitive and important tool for studies of lipid storage mechanisms, improving our understanding of phenomena underlying metabolic disorders.lipid metabolism ͉ nonlinear microscopy ͉ obesity

Shear-thinning, self-healing hydrogels are promising vehicles for therapeutic cargo delivery due to their ability to be injected using minimally invasive surgical procedures. An injectable hydrogel using a novel combination of dynamic covalent crosslinking with thermoresponsive engineered proteins is presented. Ex situ at room temperature, rapid gelation occurs through dynamic covalent hydrazone bonds by simply mixing two components: hydrazine-modified elastin-like protein (ELP) and aldehyde-modified hyaluronic acid. This hydrogel provides significant mechanical protection to encapsulated human mesenchymal stem cells during syringe needle injection and rapidly recovers after injection to retain the cells homogeneously within a 3D environment. In situ, the ELP undergoes a thermal phase transition, as confirmed by coherent anti-Stokes Raman scattering microscopy observation of dense ELP thermal aggregates. The formation of the secondary network reinforces the hydrogel and results in a tenfold slower erosion rate compared to a control hydrogel without secondary thermal crosslinking. This improved structural integrity enables cell culture for three weeks postinjection, and encapsulated cells maintain their ability to differentiate into multiple lineages, including chondrogenic, adipogenic, and osteogenic cell types. Together, these data demonstrate the promising potential of ELP-HA hydrogels for injectable stem cell transplantation and tissue regeneration. for generously sharing the uronic acid assay protocol. The authors acknowledge Brad Krajina for assistance in characterization of polymer molecular weight.