The rise in renewable energy has increased the use of DC/AC converters, which transform the direct current to alternating current. These devices, generally called inverters, are mainly used as an interface between clean energy and the grid. It is estimated that 21% of the global electricity generation capacity from renewable sources is supplied by photovoltaic systems. In these systems, a transformer to ensure grid isolation is used. Nevertheless, the transformer makes the system expensive, heavy, bulky and reduces its efficiency. Therefore, transformerless schemes are used to eliminate the mentioned disadvantages. One of the main drawbacks of transformerless topologies is the presence of a leakage current between the physical earth of the grid and the parasitic capacitances of the photovoltaic module terminals. The leakage current depends on the value of the parasitic capacitances of the panel and the common-mode voltage. At the same time, the common-mode voltage depends on the modulation strategy used. Therefore, by the manipulation of the modulation technique, is accomplished a decrease in the leakage current. However, the connection standards for photovoltaic inverters establish a maximum total harmonic distortion of 5%. In this paper an analysis of the common-mode voltage and its influence on the value of the leakage current is described. The main topologies and strategies used to reduce the leakage current in transformerless schemes are summarized, highlighting advantages and disadvantages and establishing points of comparison with similar topologies. A comparative table with the most important aspects of each converter is shown based on number of components, modes of operation, type of modulation strategy used, and the leakage current value obtained. It is important to mention that analyzed topologies present a variation of the leakage current between 0 to 180 mA. Finally, the trends, problems, and researches on transformerless grid-connected PV systems are discussed.
The objective of this work is to design and implement a scalable Field-Programmable Gate Array (FPGA)-based motion control system for DC servo motors using a parabolic velocity profile for industrial applications. The implementation in this device allows the obtaining of a fast, flexible and low-cost system. The system is divided into control, communication and closed-loop coupling. The work also addresses a comparative analysis of the most used profiles, the trapezoidal and parabolic. The comparison is made considering the energy consumption of both profiles. As a consequence of the comparison made, the velocity profile can be selected to reduce production costs by saving energy and reducing wear on machinery. The discrete models of the velocity profiles are obtained through numerical methods that permit the control blocks to be implemented in an FPGA. To reduce maintenance costs and energy consumption in servo mechanisms, the derivation of the acceleration or jerk of the motor is shown. A Graphic User Interface (GUI) is presented, which allows monitoring the position, velocity and angular acceleration of the motor shaft. In addition, the developed interface supports modification of parameters of the final position and maximum velocity in the motor. The delivered current is compared, evaluating its decrease using a parabolic velocity profile. Finally, the experimental results are illustrated.
At present, renewable energies represent 25% of the global power generation capacity. The increase in clean energy facilities is mainly due to the high levels of pollution generated by the burning of fossil fuels to satisfy the growing electricity demand. The global capacity of generating electricity from solar energy has experienced a significant increase, reaching 505 GW in 2018. Today, multilevel inverters are used in PV systems to convert direct current into alternating current. However, the use of multilevel inverters in renewable energies applications presents different challenges; for example, grid-connected systems use a transformer to avoid the presence of leakage currents. The grid-connected systems must meet at least two international standards analyzed in this work: VDE 0126-1-1 and VDE-AR-N 4105, which establish a maximum leakage current of 300 mA and harmonic distortion maximum of 5%. Previously, DC/AC converters have been studied in different industrial applications. The state-of-the-art presented in the work is due to the growing need for a greater use of clean energy and the use of inverters as an interface between these technologies and the grid. Also, the paper presents a comparative analysis of the main multilevel inverter voltage-source topologies used in transformerless PV systems. In each scheme, the advantages and disadvantages are presented, as well as the main challenges. In addition, current trends in grid-connected systems using these schemes are discussed. Finally, a comparative table based on input voltage, switching frequency, output levels, control strategy used, efficiency, and leakage current is shown.
The DC/AC converters—commonly called inverters—transform the DC into AC and are classified as Voltage-Source Inverters (VSIs) or Current-Source Inverters (CSIs). A variant of the CSIs are the Multilevel Current-Source Inverters (MCSIs). In this paper, a new predictive control strategy for an MCSI with multiple inputs and grid-connected is proposed. The control technique uses the advantages of the Sliding Mode Control (SMC) for the balance of current in the input and Predictive Control (PC) to obtain a suitable grid current, since it separates both functions. The calculations are based on conventional Kirchhoff’s Voltage Law (KVL) and knowledge of the mathematical model of the system is not required. Generally, traditional MCSIs use large input inductors (100–1000 mH). In this paper, it is achieved a reduction in size of the input inductors. Simulation results are shown to validate the proposed control.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.