Progress in thermonuclear fusion energy research based on deuterium plasmas magnetically confi ned in toroidal tokamak devices requires the development of effi cient current drive methods. Previous experiments have shown that plasma current can be driven effectively by externally launched radio frequency power coupled to lower hybrid plasma waves. However, at the high plasma densities required for fusion power plants, the coupled radio frequency power does not penetrate into the plasma core, possibly because of strong wave interactions with the plasma edge. Here we show experiments performed on FTU (Frascati Tokamak Upgrade) based on theoretical predictions that nonlinear interactions diminish when the peripheral plasma electron temperature is high, allowing signifi cant wave penetration at high density. The results show that the coupled radio frequency power can penetrate into high-density plasmas due to weaker plasma edge effects, thus extending the effective range of lower hybrid current drive towards the domain relevant for fusion reactors.

FAST is a new machine proposed to support ITER experimental exploitation as well as to anticipate DEMO relevant physics and technology. FAST is aimed at studying, under burning plasma relevant conditions, fast particle (FP) physics, plasma operations and plasma wall interaction in an integrated way. FAST has the capability to approach all the ITER scenarios significantly closer than the present day experiments using deuterium plasmas. The necessity of achieving ITER relevant performance with a moderate cost has led to conceiving a compact tokamak (R = 1.82 m, a = 0.64 m) with high toroidal field (B T up to 8.5 T) and plasma current (I p up to 8 MA). In order to study FP behaviours under conditions similar to those of ITER, the project has been provided with a dominant ion cyclotron resonance heating system (ICRH; 30 MW on the plasma). Moreover, the experiment foresees the use of 6 MW of lower hybrid (LHCD), essentially for plasma control and for non-inductive current drive, and of electron cyclotron resonance heating (ECRH, 4 MW) for localized electron heating and plasma control. The ports have been designed to accommodate up to 10 MW of negative neutral beams (NNBI) in the energy range 0.5-1 MeV. The total power input will be in the 30-40 MW range under different plasma scenarios with a wall power load comparable to that of ITER (P /R ∼ 22 MW m −1). All the ITER scenarios will be studied: from the reference H mode, with plasma edge and ELMs characteristics similar to the ITER ones (Q up to ≈1.5), to a full current drive scenario, lasting around 170 s. The first wall (FW) as well as the divertor plates will be of tungsten in order to ensure reactor relevant

Abstract. The ITER electron cyclotron (EC) upper port antenna (or launcher) is nearing completion of the detailed design stage and will soon be starting the final build to print design. The main objective of this launcher is to drive current locally to stabilise the NTMs (depositing ECCD inside of the island that forms on either the q=3/2 or 2 rational magnetic flux surfaces) and control the sawtooth instability (deposit ECCD near the q=1 surface). The launcher should be capable of steering the focused beam deposition location to the resonant flux surface over the range in which the q=1, 3/2 and 2 surfaces are expected to be found, for the various plasma equilibria susceptible to the onset of NTMs and sawteeth. The aim of this paper is to provide the design status of the principle components that make up the launcher: port plug, mm-wave system and shield block components. The port plug represents the chamber that provides a rigid support structure that houses the mm-wave and shield blocks. The mm-wave system is comprised of the components used to guide the RF beams through the port plug structure and refocus the beams far into the plasma. The shield block components are used to attenuate the nuclear radiation from the burning plasma, protecting the fragile in-port components and reducing the neutron streaming through the port assembly. The design of these three subsystems is described, in addition, the relevant thermo-mechanical and electro-magnetic analysis are reviewed for the critical design issues.

Abstract.A fast directional switch (FADIS) is described, which allows controlled switching of high-power microwaves between two outputs. A possible application could be synchronous stabilization of neoclassical tearing modes (NTM). Generally, the device can be used to share the installed EC power between different types of launchers or different applications (e.g. in ITER, midplane / upper launcher). The switching is performed electronically without moving parts by a small frequency-shift keying of the gyrotron (some tens of MHz), and a narrow-band diplexer. The device can be operated as a beam combiner also, which offers attractive transmission perspectives in multi-megawatt ECRH systems. In addition, these diplexers are useful for plasma diagnostic systems employing high-power sources due to their filter characteristics. The principle and the design of a four-port quasi-optical resonator diplexer is presented. Lowpower measurements of switching contrast, mode purity and efficiency show good agreement with theory. Preliminary frequency modulation characteristics of gyrotrons are shown, and first results from high-power switching experiments using the ECRH system for W7-X are presented.

Perturbative and steady-state heat transport of FTU tokamak in current ramp-up discharges are investigated by means of modulated electron cyclotron heating (MECH). Perturbative and steady-state transport experiments are coherent with an electron heat transport which switches from low to high values when electron temperature gradient length reaches a threshold value 1/L T c . The threshold value 1/L T c is shown to be proportional to the ratio s/q.The experimental findings are compared to predictions of an empirical model based on the assumption of a threshold gradient length, L T c (1/L T = |∇T e /T e |), in the electron temperature T e below which electron thermal diffusivity, χ e , switches from low to high values. Plasma responses to steady state and MECH are modelled assuming the electron diffusivity as χ PB = χ 0 + αT