Two-layered blood-lipid phantom and method to determine absorption and oxygenation employing changes in moments of DTOFs

Abstract

Near-infrared spectroscopy (NIRS) is an established technique for measuring tissue oxygen saturation (StO2), which is of high clinical value. For tissues that have layered structures, it is challenging but clinically relevant to obtain StO2 of the different layers, e.g. brain and scalp. For this aim, we present a new method of data analysis for time-domain NIRS (TD-NIRS) and a new two-layered blood-lipid phantom. The new analysis method enables accurate determination of even large changes of the absorption coefficient (Δµa) in multiple layers. By adding Δµa to the baseline µa, this method provides absolute µa and hence StO2 in multiple layers. The method utilizes (i) changes in statistical moments of the distributions of times of flight of photons (DTOFs), (ii) an analytical solution of the diffusion equation for an N-layered medium, (iii) and the Levenberg–Marquardt algorithm (LMA) to determine Δµa in multiple layers from the changes in moments. The method is suitable for NIRS tissue oximetry (relying on µa) as well as functional NIRS (fNIRS) applications (relying on Δµa). Experiments were conducted on a new phantom, which enabled us to simulate dynamic StO2 changes in two layers for the first time. Two separate compartments, which mimic superficial and deep layers, hold blood-lipid mixtures that can be deoxygenated (using yeast) and oxygenated (by bubbling oxygen) independently. Simultaneous NIRS measurements can be performed on the two-layered medium (variable superficial layer thickness, L), the deep (homogeneous), and/or the superficial (homogeneous). In two experiments involving ink, we increased the nominal µa in one of two compartments from 0.05 to 0.25 cm−1, L set to 14.5 mm. In three experiments involving blood (L set to 12, 15, or 17 mm), we used a protocol consisting of six deoxygenation cycles. A state-of-the-art multi-wavelength TD-NIRS system measured simultaneously on the two-layered medium, as well as on the deep compartment for a reference. The new method accurately determined µa (and hence StO2) in both compartments. The method is a significant progress in overcoming the contamination from the superficial layer, which is beneficial for NIRS and fNIRS applications, and may improve the determination of StO2 in the brain from measurements on the head. The advanced phantom may assist in the ongoing effort towards more realistic standardized performance tests in NIRS tissue oximetry. Data and MATLAB codes used in this study were made publicly available.

Muscle Oximetry in Sports Science: An Updated Systematic Review

“…However, absolute values obtained during exercise were generally not comparable between devices unless corrected by physiological calibration after arterial occlusion. This indicates that further efforts should be made to standardize all muscle oximeters, for example, by using tissue-simulating phantoms [ 207 ] and following the guidelines of ISO 80601-2-85:2021 (Medical electrical equipment—Part 2–85: particular requirements for the basic safety and essential performance of cerebral tissue oximeter equipment). The cumbersome instruments, developed for brain oximetry measurements, can be utilized for muscle studies.…”

Tissue mimicking materials and finger phantom design for pulse oximetry

“…Although TiO 2 as a scatterer in the outer matrix and water-soluble nigrosin as an absorber in the vessels proved to be sufficient in the preliminary pulsatility tests required for PPG signal detection, future pulse oximetry experiments could be enhanced by incorporating both static and dynamic absorption values that mimic real tissue. For example, via the addition of a thin epidermal-mimicking layer like those used by Afshari et al [ 13 ] and exploring alternative blood-mimicking fluids, like those used by Sudakou et al [ 21 ].…”

“…The necessity of such standardization has been underscored, advocating for the development of optical phantoms as a solution that offers repeatable and controlled testing environments that are both cost-effective and less time-consuming compared to in vivo trials [ 20 ]. Complementing this, several researchers have innovated a two-layered phantoms, which, by incorporating whole human blood into a turbid medium, enables the simulation of dynamic oxygen saturation levels ranging from 0 to 100%, thereby mimicking the complex multi-layered tissue structures found in vivo and enhancing the fidelity of tissue oximetry testing [ 13 , 21 ]. Further emphasizing the importance of anatomical accuracy, researchers have contributed to the field by formulating solid phantoms that not only replicate the 3D shapes of human organs but also possess the properties necessary for thorough calibration and performance analysis of biomedical optics devices, thus paving the way for more precise and anatomically correct biophotonic applications [ 22 , 23 ].…”

Time-domain diffuse correlation spectroscopy at large source detector separation for cerebral blood flow recovery

“…As the phantom absorption does not influence the dynamic of properties [ 27 ], no absorber was added to the solutions. To set the desired reduced scattering coefficient, various concentrations of the SMOFlipid were added into each mixture following the recipe in [ 28 , 29 ]. Moments of the measured DTOFs were used to calculate the absorption coefficient μ a and the reduced scattering coefficient μ ′ s [ 30 ].…”