Transformation Temperatures and Electrochemical behavior of Polycrystalline Fe-Doped Ni-Mn-Ga and Co-Ni-Ga Alloys

Sánchez-Carrillo, M.

doi:10.20964/2018.07.08

Cited by 1 publication

(1 citation statement)

References 31 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Corrosion rate measurements of the SLMed samples were calculated using the Stern–Geary relationship [ 40 ], Equation (1):

where

is the Stern–Geary constant,

is the potential gradient,

is the current gradient, and

is the polarization resistance (

). Note that in Equation (2), the Stern–Geary constant can be calculated from the anodic (

) and cathodic

Tafel slopes [ 41 ].

…”

Section: Resultsmentioning

confidence: 99%

Corrosion Resistance Measurement of 316L Stainless Steel Manufactured by Selective Laser Melting

et al. 2021

View full text Add to dashboard Cite

Selective laser melting (SLM) technology is ushering in a new era of advanced industrial production of metal components. It is of great importance to understand the relationship between the surface features and electrochemical properties of manufactured parts. This work studied the influence of surface orientation on the corrosion resistance of 316L stainless-steel (SS) components manufactured with SLM. The corrosion resistance of the samples was measured using linear polarization resistance (LPR) and electromechanical noise (EN) techniques under three different environments, H2O, 3.5 wt.% NaCl, and 20% H2OSO4,, analyzing the horizontal (XY) and vertical (XZ) planes. The microstructure and morphology of the samples were obtained by optical (OM) and scanning electron microscopy (SEM). The obtained microstructure showed the grains growing up from the fusion line to the melt pool center and, via SEM-EDS, the presence of irregular and spherical pores was observed. The highest corrosion rate was identified in the H2SO4 solution in the XZ plane with 2.4 × 10−2 mm/year and the XY plane with 1.31 × 10−3 mm/year. The EN technique along with the skewness factor were used to determine the type of corrosion that the material developed. Localized corrosion was observed in the electrolyte, for the XY and XZ planes (−1.65 and −0.012 skewness factors, respectively), attacking mainly the subgrains of the microstructure and, in some cases, the pores, caused by Cl ions. and solutions presented a uniform corrosion mechanism for the two observed orientations. The morphology identified by SEM was correlated with the results obtained from the electrochemical techniques.

show abstract

“…Corrosion rate measurements of the SLMed samples were calculated using the Stern–Geary relationship [ 40 ], Equation (1):

where

is the Stern–Geary constant,

is the potential gradient,

is the current gradient, and

is the polarization resistance (

). Note that in Equation (2), the Stern–Geary constant can be calculated from the anodic (

) and cathodic

Tafel slopes [ 41 ].

…”

Section: Resultsmentioning

confidence: 99%

Corrosion Resistance Measurement of 316L Stainless Steel Manufactured by Selective Laser Melting

et al. 2021

View full text Add to dashboard Cite

show abstract

Transformation Temperatures and Electrochemical behavior of Polycrystalline Fe-Doped Ni-Mn-Ga and Co-Ni-Ga Alloys

Cited by 1 publication

References 31 publications

Corrosion Resistance Measurement of 316L Stainless Steel Manufactured by Selective Laser Melting

Corrosion Resistance Measurement of 316L Stainless Steel Manufactured by Selective Laser Melting

Contact Info

Product

Resources

About