The effect of iron content on fatigue lifetime of AlZn10Si8Mg cast alloy

Závodská, Denisa; Kuchariková, Lenka; Tillová, Eva; Guagliano, Mario; Chalupová, Mária; Uhríčik, Milan; Belán, Juraj

doi:10.1016/j.ijfatigue.2019.105189

Cited by 9 publications

(2 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Alumina particles significantly improved the alloy's wear resistance and thermal conductivity. Mirza et al (2021) [7] examined how ferric…”

Section: Introductionmentioning

confidence: 99%

Influence of Alumina, Ferric Oxide, and Mn as Composites on the Properties of Recycled Aluminium Alloy

Srinath,

Bhagyanathan,

Melwyn J.

et al. 2024

MSF

View full text Add to dashboard Cite

Recycling of aluminium alloys is gaining significant attention due to its economic and environmental benefits. However, close loop recycled aluminium alloys can be adversely affected by impurities and alloying elements present in the recycled feedstock. In this study, the influence of three composites, namely alumina (Al2O3), ferric oxide (Fe2O3), and manganese (Mn), on the properties of recycled aluminium taldon scraps was investigated to enhance the tensile behaviour of the alloys. The effects of these composites on the mechanical properties, microstructure, and corrosion behaviour of the recycled aluminium alloys were evaluated through experimental characterization techniques. The results showed that the addition of these composites had a significant influence on the properties of recycled aluminium alloys, providing insights into the potential for improving the performance of recycled aluminium alloys through composite additions. The addition of Al2O3 enhanced the tensile strength by 44.18 % and the variation can be attributed to the strengthening of the dendritic zones by the formation of α-Al.

show abstract

“…Alumina particles significantly improved the alloy's wear resistance and thermal conductivity. Mirza et al (2021) [7] examined how ferric…”

Section: Introductionmentioning

confidence: 99%

Influence of Alumina, Ferric Oxide, and Mn as Composites on the Properties of Recycled Aluminium Alloy

Srinath,

Bhagyanathan,

Melwyn J.

et al. 2024

MSF

View full text Add to dashboard Cite

show abstract

“…Strain‐controlled low cycle fatigue (LCF) behavior is required in the design and life prediction of automotive components, leading to many studies on the LCF of cast Al–Si alloys in relation to the effect of alloying elements and microstructures 7,16–19 . For example, the dependence of fatigue life on eutectic Si particle morphologies and other intermetallic particles in Al–Si alloys was studied at room and elevated temperatures 20–22 . The effect of alloying elements (such as transition metals Ti, V, Zr, Mn, etc.)…”

Section: Introductionmentioning

confidence: 99%

Cyclic deformation behavior and fatigue life prediction of an automotive cast aluminum alloy: A new method of determining intrinsic fatigue toughness

Zeng

et al. 2021

Fatigue Fract Eng Mat Struct

View full text Add to dashboard Cite

The aim of this study was to identify cyclic deformation behavior of a high‐pressure die‐cast Silafont®‐36 automotive cast aluminum alloy consisting of heterogeneous composite‐like microstructures of nearly circular eutectic silicon particles embedded in Al matrix, with particular attention to fatigue life prediction. The alloy exhibited superior fatigue resistance at higher strain amplitudes, where cyclic hardening occurred. The fatigue life of the alloy could be well predicted via a strain‐energy density based accumulative damage model using a new method proposed to calculate the intrinsic fatigue toughness. The predicted fatigue life was in good agreement with the experimental life, and also lay in‐between the results obtained via other methods. Fatigue crack initiation was observed to occur from the sample surface or near‐surface defects and crack propagation was characterized by fatigue striations along with tear ridges in the primary Al‐grains.

show abstract

Effect of milling time on structural, physical and tribological behavior of a newly developed Ti-Nb-Zr alloy for biomedical applications

Hamadi,

Fellah,

Hezil

et al. 2024

Advanced Powder Technology

View full text Add to dashboard Cite

The effect of iron content on fatigue lifetime of AlZn10Si8Mg cast alloy

Cited by 9 publications

References 22 publications

Influence of Alumina, Ferric Oxide, and Mn as Composites on the Properties of Recycled Aluminium Alloy

Influence of Alumina, Ferric Oxide, and Mn as Composites on the Properties of Recycled Aluminium Alloy

Cyclic deformation behavior and fatigue life prediction of an automotive cast aluminum alloy: A new method of determining intrinsic fatigue toughness

Effect of milling time on structural, physical and tribological behavior of a newly developed Ti-Nb-Zr alloy for biomedical applications

Contact Info

Product

Resources

About