Static simulation to horse shoes alternative materials based basic polymeric foam reinforced fiberglass with ANSYS software

Siregar, Riski Elpari; Syam, Bustami; Wirjosentono, Basuki; Muttaqin, Maraghi

doi:10.1088/1742-6596/1116/4/042036

Cited by 2 publications

(2 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The smaller the diameter of the copper tube, the stronger the shearing effect on the polymer solution. By physical experiments [34,35], we identified that when the inner diameter of the copper tube was 5.8 mm, the influence on the polymer's shearing viscosity would be minimized, so we designed an 86-hole copper flow-guiding tube model.…”

Section: Design Ideamentioning

confidence: 99%

Optimization Design and Analysis of Polymer High Efficiency Mixer in Offshore Oil Field

et al. 2020

View full text Add to dashboard Cite

The degree of polymer-water mixing in high-pressure pipelines on offshore oilfields usually influences the polymer solution’s performance. To realize efficient mixing of the polymer mother liquor with dilution water in the high-pressure pipeline, a high-efficiency mixer is designed and optimized. The designed mixer consists of four parts: a T-shaped pipe as the main body, an inlet flow-splitting plate, a stainless-steel flow-guiding tube, and an outlet flow-splitting plate. Mathematical models are built by using computational fluid dynamics (CFD) and the mixing effects are compared by using Fluent. The research results show that compared with conventional T-shaped mixers, the designed high-efficiency mixer has better mixing performance and increases the mixing rate to 80%. To optimize the mixing rate, the length of the stainless-steel tube is increased and the tube is perforated to guide the flow. The result shows that boring holes along straight lines around the tube can achieve good optimization effect and increase the mixing rate to 95%. The designed high-efficiency mixer can effectively improve the dissolving efficiency and solve problems in polymer-water mixing in the high-pressure pipeline.

show abstract

Section: Design Ideamentioning

confidence: 99%

Optimization Design and Analysis of Polymer High Efficiency Mixer in Offshore Oil Field

et al. 2020

View full text Add to dashboard Cite

show abstract

“…The material used, chopped strand mat (CSM) glass fiber was chopped and varied with 2 (two) different amounts of composition [6]- [10]. Analysis of the force applied to the crossbar (portal) of polymer material using BTQN 157 EX fiberglass resin with MEKPO catalyst in the form of an impact test in experimental testing to determine the position of damage that occurs in the crossbar and compare it with the position of the damage in the simulation results of ANSYS [11]- [13]. Before running the simulation, the material characteristics data will be used to be entered into the simulation analysis.…”

Section: Introductionmentioning

confidence: 99%

Structural Analysis of Parking Barrier Made of Polymeric Resin Using Ansys Software

et al. 2023

View full text Add to dashboard Cite

A barrier gate is a stopping tool that has a security function in a place such as an office or agency entrance. This study aims to examine the response of the beam structure of the polymer composite material due to the support test. The parking portal material in this research is BQTN 157 EX resin, MEKPO catalyst, fiberglass. There are two parking portal compositions with impact test heights of 2 m and 4 m which will be simulated with ansys software. Overall, from two types of compositions, namely polymeric reinforced fiberglass composition A and composition B by looking at the results of the equivalent stress distribution (von-mises), it is concluded that polymeric reinforced fiberglass composition A has a higher maximum stress than polymeric reinforced fiberglass composition. reinforced with fiberglass composition B. From the comparison between simulation and experiment, it is known that the composition of rod A has a different damage position between simulation and experiment. While the composition of rod B in the simulation of the same damage position occurs, namely in the crossbar area connected to the transmission shaft and the experimental also has a damage position in the crossbar area connected to the transmission shaft.

show abstract

Static simulation to horse shoes alternative materials based basic polymeric foam reinforced fiberglass with ANSYS software

Cited by 2 publications

References 1 publication

Optimization Design and Analysis of Polymer High Efficiency Mixer in Offshore Oil Field

Optimization Design and Analysis of Polymer High Efficiency Mixer in Offshore Oil Field

Structural Analysis of Parking Barrier Made of Polymeric Resin Using Ansys Software

Contact Info

Product

Resources

About