Rapid self-healing in IR-responsive plasmonic indium tin oxide/polyketone nanocomposites

Araya-Hermosilla, Esteban; Gabbani, Alessio; Mazzotta, Arianna; Ruggeri, Marina; Orozco, Felipe; Cappello, Valentina; Gemmi, Mauro; Bose, Ranjita K.; Picchioni, Francesco; Pineider, Francesco; Mattoli, Virgilio; Pucci, Andrea

doi:10.1039/d2ta01286c

Cited by 13 publications

(10 citation statements)

References 68 publications

(86 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Notably, the reaction of the 1,4-dicarbonyl units of PK with primary amine leads to the formation of N-substituted pyrrole units through the Paal-Knorr reaction [21]. This reaction occurs without using any solvents and has the advantage of having only water as a secondary product [22,23]. The functionalization of PKs with imidazole groups allows the introduction of quaternary ammonium cation groups with two different types of haloalkanes.…”

Section: Introductionmentioning

confidence: 99%

Polyketone-Based Anion-Exchange Membranes for Alkaline Water Electrolysis

et al. 2023

Self Cite

View full text Add to dashboard Cite

Anion-exchange membranes (AEMs) are involved in a wide range of applications, including fuel cells and water electrolysis. A straightforward method for the preparation of efficient AEMs consists of polymer functionalization with robust anion-exchange sites. In this work, an aliphatic polyketone was functionalized with 1-(3-aminopropyl)imidazole through the Paal–Knorr reaction, with a carbonyl (CCO %) conversion of 33%. The anion-exchange groups were generated by the imidazole quaternization by using two different types of alkyl halides, i.e., 1,4-iodobutane and 1-iodobutane, with the aim of modulating the degree of crosslinking of the derived membrane. All of the membranes were amorphous (Tg ∼ 30 °C), thermally resistant up to 130 °C, and had a minimum Young’s modulus of 372 ± 30 MPa and a maximum of 86 ± 5 % for the elongation at break for the least-crosslinked system. The ionic conductivity of the AEMs was determined at 25 °C by electrochemical impedance spectroscopy (EIS), with a maximum of 9.69 mS/cm, i.e., comparable with that of 9.66 mS/cm measured using a commercially available AEM (Fumasep-PK-130). Future efforts will be directed toward increasing the robustness of these PK-based AEMs to meet all the requirements needed for their application in electrolytic cells.

show abstract

Section: Introductionmentioning

confidence: 99%

Polyketone-Based Anion-Exchange Membranes for Alkaline Water Electrolysis

et al. 2023

Self Cite

View full text Add to dashboard Cite

show abstract

“…Moreover, given the long wavelength at which they exhibit plasmonic properties, Mie scattering is further reduced in these nanostructures, and absorption is dominating, which is the crucial contribution to convert photons into heat. 49 All these features make colloidal dispersions of ITO NPs very attractive as anti-counterfeiting inks exploiting the thermoplasmonic effect upon infrared light illumination.…”

Section: Introductionmentioning

confidence: 99%

Invisible Thermoplasmonic Indium Tin Oxide Nanoparticle Ink for Anti-counterfeiting Applications

Mazzotta

Gabbani

Carlotti

et al. 2022

ACS Appl. Mater. Interfaces

Self Cite

View full text Add to dashboard Cite

In this study, we present a thermoplasmonic transparent ink based on a colloidal dispersion of indium tin oxide (ITO) nanoparticles, which can offer several advantages as anti-counterfeiting technology. The custom ink could be directly printed on several substrates, and it is transparent under visible light but is able to generate heat by absorption of NIR radiation. Dynamic temperature mapping of the printed motifs was performed by using a thermal camera while irradiating the samples with an IR lamp. The printed samples presented fine features (in the order of 75 μm) and high thermal resolution (of about 250 μm). The findings are supported by thermal finite-element simulations, which also allow us to explore the effect of different substrate characteristics on the thermal readout. Finally, we built a demonstrator comprising a QR Code invisible to the naked eye, which became visible in thermal images under NIR radiation. The high transparency of the printed ink and the high speed of the thermal reading (figures appear/disappear in less than 1 s) offer an extremely promising strategy toward low-cost, scalable production of photothermally active invisible labels.

show abstract

“…In this work, we aimed at developing innovative multifunctional polymeric materials, containing both germicide and polar moieties in their molecular structures. Based on our experience in the synthesis of functionalized polyketones, [14][15][16][17][18] spectrum of 2,3,4-triacetoxy-6-tosyl-a-methyl-D-glucopyranoside (2). Fig.…”

Section: Introductionmentioning

confidence: 99%

“…In this work, we aimed at developing innovative multifunctional polymeric materials, containing both germicide and polar moieties in their molecular structures. Based on our experience in the synthesis of functionalized polyketones, 14–18 we inserted quaternary ammonium groups on polyketone to make it able to kill pathogens and, at the same time, sugar portions to increase its hydrophilic properties on cellulose-based materials, such as paper objects and surfaces. These functional copolymers were prepared by grafting the new moieties on a perfect alternating aliphatic polyketone via the Paal–Knorr reaction.…”

Section: Introductionmentioning

confidence: 99%