Mechanism of Strong Formation of {111} Recrystallization Texture of Cold Rolled IF Steel Sheet with {111} Hot Band Texture

Okuda, Koichi; Sakata, Kei; Eloot, Katrien; Furukimi, Osamu; Obara, Takashi

doi:10.2355/tetsutohagane1955.85.8_633

Cited by 6 publications

(1 citation statement)

References 13 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Many studies are being performed for clarifying the mechanism of such a variant selection and for defining the rotation angle around the axis. [12][13][14] In the present discussion, the selection is supposed to be inevitable and the rotation angle is supposed to be 30°. To be concrete, for on RD//͗110͘Ϯ20°in the same relation as above.…”

Section: The Development Of the Texture Suppressing The Earingmentioning

confidence: 99%

Change in Earing of Low-carbon Aluminum-killed Steel Sheets with Hot- and Cold-rolling Conditions.

2000

View full text Add to dashboard Cite

Experiments have been conducted to investigate the effect of hot-and cold-rolling conditions on earing. It was shown that the earing of cold-rolled and annealed sheets increases with an increase in cold-rolling reduction. On the other hand, the earing decreases with a finishing temperature below Ar3 temperature in hot rolling, the effect of the finishing temperature below Ar3 being minimal in connection with a hot-rolling reduction. The earing increases as the hot-rolling reduction increases and a finishing temperature below Ar3 decreases. With a lower coiling temperature, a deformed structure remains in hot-rolled band and the earing is increased. These increases or decreases in earing depend on the growth or suppression of 45°earing arising from the texture of RD//͗110͘Ϯ20°. The texture development is affected by the initial texture and initial grain size before cold-rolling, and the earing is controlled by the effect of a balance between the same.

show abstract

Section: The Development Of the Texture Suppressing The Earingmentioning

confidence: 99%

Change in Earing of Low-carbon Aluminum-killed Steel Sheets with Hot- and Cold-rolling Conditions.

2000

View full text Add to dashboard Cite

show abstract

Crystal Plasticity Analysis of Anisotropic Work Hardening Behavior in IF steel

Tsunemi

Kubo

Yonemura

et al. 2017

Procedia Engineering

View full text Add to dashboard Cite

Recrystallization of Isolated Deformed Grains in High Purity Iron

Okuda¹,

Seto²

2015

ISIJ Int.

Self Cite

View full text Add to dashboard Cite

Early stage of recrystallization behavior was investigated in high purity deformed iron with isolated crystal grains to elucidate the mechanism of recrystallization. Recrystallization of the isolated deformed grains was greater than that of the bi-crystal matrix. The recrystallized grains were observed in the RD×ND section at the tip portion of the deformed isolated grains extending in the rolling direction. Recrystallized grains were also observed inside the deformed isolated grains. The crystal orientations of the recrystallized nucleus were positioned where they were in the perimeter portion of the orientation spread of the deformed matrix, or there may have been the intermediate orientation between the matrix and the isolated grains.

show abstract

Mechanism of Strong Formation of {111} Recrystallization Texture of Cold Rolled IF Steel Sheet with {111} Hot Band Texture

Cited by 6 publications

References 13 publications

Change in Earing of Low-carbon Aluminum-killed Steel Sheets with Hot- and Cold-rolling Conditions.

Change in Earing of Low-carbon Aluminum-killed Steel Sheets with Hot- and Cold-rolling Conditions.

Crystal Plasticity Analysis of Anisotropic Work Hardening Behavior in IF steel

Recrystallization of Isolated Deformed Grains in High Purity Iron

Contact Info

Product

Resources

About