Fabrication of Hybrid Mg/(Al2O3p + SiCp + Grp) Metal Matrix Composite on Developed Gas Injection Liquid Stir Casting Setup

Hira, Jaspreet; Mangal, S. K.; Manna, Alakesh

doi:10.1007/s13369-015-1755-1

Cited by 11 publications

(2 citation statements)

References 18 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Hira et al [14], used the gas injection liquid stir casting to create an experimental workpiece specimen including the hard reinforced particles, which has been utilized for the work study. The dimension of the workpiece including the length 250 mm and diameter 90 mm respectively.…”

Section: Methodsmentioning

confidence: 99%

The effect on the tool flank wear width VBmax during turning of Hybrid Mg/(8wt% SiC(p) +2wt% Al2O3(p) +1wt% Gr(p) MMC using PVD coated cermet tool

Hira¹,

Manna

Jha³

et al. 2022

IOP Conf. Ser.: Mater. Sci. Eng.

Self Cite

View full text Add to dashboard Cite

In this study Taguchi Optimization Technique was used, followed by ANOVA to evaluate the machinability i.e. turning of a hybrid Mg/(8wt%SiCp+2wt%Al2O3p+1wt%Grp) MMC using PVD coated cermet tool under the dry turning conditions. Several experiments were conducted using the L27 (313) orthogonal array on NH26 automated lather machine. ANOVA was used to determine the impression of the turning parameter on the VBmax of the tool flank. The finding of the research work investigated that the cutting speed in the dominant factor influence the tool wear width. The confirmation test revealed that the Taguchi technique has been successful in the optimization of the machining parameters for minimum tool wear. The optimal parameter arrangement for minimum tool wear width is at cutting speed of 120 m/min, with the feed rate of 0.4 mm/rev and depth of cut at 0.75 mm. The scanning electron microscope images revealed notches, groves and pits on the tool flank face that is clearly visible at different magnification units. Herein, this paper discuss about several reported synthesis techniques, various characterization techniques used for structural and surface properties identifications, different morphologies and various potential applications of transition metal oxide based nanocomposites.

show abstract

Section: Methodsmentioning

confidence: 99%

The effect on the tool flank wear width VBmax during turning of Hybrid Mg/(8wt% SiC(p) +2wt% Al2O3(p) +1wt% Gr(p) MMC using PVD coated cermet tool

Hira¹,

Manna

Jha³

et al. 2022

IOP Conf. Ser.: Mater. Sci. Eng.

Self Cite

View full text Add to dashboard Cite

show abstract

“…An inert environment inside the furnace can be created by supplying inert gases gas like helium, argon, etc. [17,18]. Besides the fabrication techniques, the reinforcement type plays another important role to achieve the desired physical and microstructural properties of the composites.…”

Section: Introductionmentioning

confidence: 99%

Characterization of aluminium metal matrix composite fabricated by gas injection bottom pouring vacuum multi-stir casting process

Kataria¹,

Mangal²

2018

Self Cite

View full text Add to dashboard Cite

In the present work, a newly developed gas injection bottom pouring vacuum stir casting technique has been envisaged for the fabrication of Aluminium MMCs which is a fully automated and one of its kind. Aluminium 6063-T6 alloy is used as the matrix, and the aluminium oxide (Al2O3) particles are taken as reinforcement. Different experiments have been performed on the fabricated MMCs to ascertain its mechanical and morphological properties. The presence of various elements and grain morphology of the fabricated MMCs are confirmed by Energy Dispersive Spectroscopy (EDS), Scanning Electron Microscope (SEM) and mapping. The experimental results revealed that the hardness of Al/Al2O3MMC had increased by 1.71 times and maximum tensile strength had increased by 1.27 times in comparison to the monolithic aluminium alloy. The results establish that the proposed methodology of MMC fabrication can be effectively utilized for fabrication of homogeneously reinforced MMCs for various engineering and industrial applications.

show abstract

The Effect of Friction Stir Welding on the Mechanical Properties of Hybrid Mg/(SiCp + Al2O3p + Grp)-MMC

Hira

Manna

Mangal

et al. 2021

Lecture Notes in Mechanical Engineering

View full text Add to dashboard Cite

Fabrication of Hybrid Mg/(Al2O3p + SiCp + Grp) Metal Matrix Composite on Developed Gas Injection Liquid Stir Casting Setup

Cited by 11 publications

References 18 publications

The effect on the tool flank wear width VBmax during turning of Hybrid Mg/(8wt% SiC(p) +2wt% Al2O3(p) +1wt% Gr(p) MMC using PVD coated cermet tool

The effect on the tool flank wear width VBmax during turning of Hybrid Mg/(8wt% SiC(p) +2wt% Al2O3(p) +1wt% Gr(p) MMC using PVD coated cermet tool

Characterization of aluminium metal matrix composite fabricated by gas injection bottom pouring vacuum multi-stir casting process

The Effect of Friction Stir Welding on the Mechanical Properties of Hybrid Mg/(SiCp + Al2O3p + Grp)-MMC

Contact Info

Product

Resources

About