Evaluation of the Inertial Response of Variable Speed Wind Turbines Based on DFIG using Backstepping for a Frequency Control

This research work deals with the modelling, control and simulation of a wind turbine based on the doubly fed induction generator (DFIG) in the current sensor’s failure event. We present in the first time the model of the wind energy conversion system based on the DFIG and the control by active disturbances rejection control (ADRC) optimized by genetic algorithm. Particular focus is directed towards on a technique for detection, identification, isolation and reconfiguration of current sensor signals after failure. The combination of the two preceding techniques makes it possible to have a fault tolerant control to sensor faults which ensures continuity of service in all circumstances. The robustness of the proposed technique is tested under the MATLAB/Simulink environment.

show abstract

“…The DFIG model is obtained from the dynamic equations of stator and rotor fluxes (1) and voltages (2) in the dq reference [9], [10]…”

Section: Research Methods 21 Dfig Modelingmentioning

confidence: 99%

“…In this block diagram, the DFIG stator is directly connected to the grid and the rotor is connected to the grid through two converters, rotor side converter (RSC) and grid side converter (GSC), and a DC link. Usually, the RSC controls the produced powers, and the GSC controls the DC link voltage [9], [11], [12].…”

Section: Research Methods 21 Dfig Modelingmentioning

confidence: 99%

Fault tolerant control for DFIG wind turbine controlled by ADRC and optimized by genetic algorithm

Aissaoui

Elmouhi

Essadki

et al. 2023

IJPEDS

View full text Add to dashboard Cite

show abstract

“…We have considered the stator flux control oriented along the d axis of the two-phase reference. It is also considered that the stator resistance Rs is negligible during the model computing [12], [17], [21], [22]. So, we deduce:…”

Section: Dfig Modellingmentioning

confidence: 99%

“…The equations which describe the electric part of the generator in the two-phase reference are given by the following relations [12], [21]: 677 the equation describing the mechanical part is as shown in [21]:…”

Section: Dfig Modellingmentioning

confidence: 99%

Robust control of wind turbine based on doubly-fed induction generator optimized by genetic algorithm

Elmouhi

Essadki

Elaimani³

2022

IJPEDS

Self Cite

View full text Add to dashboard Cite

In this research paper we will cover the study of the modelling and the control methods of the variable speed wind turbine based on doubly-fed induction generator (DFIG). It represents the most stressed structure given its distinctive characteristics. To control the electrical powers generated by this system independently, the vector control with the stator flux orientation is founded according to two techniques: i) the control of the powers by the backstepping technique and ii) the robust control based on the active disturbances rejection control. After the synthesis of the controllers of those two methods, their performances will be tested and compared to evaluate their effectiveness. We are mainly interested in the robustness test of the two control strategies with respect to the internal parameters’ fluctuation of the generator. The computing of the different parameters regulators of these two strategies is carried out using a genetic algorithm. This computing method makes it possible to arrive at an optimal solution of the DFIG power control. The different parts are simulated using MATLAB/Simulink environment.

show abstract

“…In DFIG-based WECS, the generator stator is connected directly to the grid and the rotor is connected to the grid through two power electronics converters and a DC link (Elmouhi et al, 2019).…”

Section: Introductionmentioning

confidence: 99%

Robustness Comparison of Synthetic Inertia Strategies for Doubly Fed Induction Generators under Different Operating Conditions

Souza

Santos

Filho

et al. 2020

Anais Do Simpósio Brasileiro De Sistemas Elétricos 2020

View full text Add to dashboard Cite

Due to the increasing penetration of Renewable Energy Sources (RES) such as wind energy in electrical grids, Wind Energy Conversion Systems (WECS) participation in primary control is becoming required including the Doubly Fed Induction Generator (DFIG)-based WECS. High integration of large scale DFIG-based WECS brings new challenges to their primary control support, and more strongly due to the wind condition and grid parameter uncertainties. One of the most used types of control strategy for DFIG-based WECS primary support is the synthetic inertia, however, robustness of these techniques have not been tested. In this work three synthetic inertia control strategies will be tested under different operating conditions of wind speed, frequency and voltage sag. For testing the DFIG-based WECS, it was modeled on ATP including its control systems and the results quantified the controllers robustness on the tested controllers with respect to transient frequency behavior.

show abstract

Evaluation of the Inertial Response of Variable Speed Wind Turbines Based on DFIG using Backstepping for a Frequency Control

Cited by 6 publications

References 0 publications

Fault tolerant control for DFIG wind turbine controlled by ADRC and optimized by genetic algorithm

Fault tolerant control for DFIG wind turbine controlled by ADRC and optimized by genetic algorithm

Robust control of wind turbine based on doubly-fed induction generator optimized by genetic algorithm

Robustness Comparison of Synthetic Inertia Strategies for Doubly Fed Induction Generators under Different Operating Conditions

Contact Info

Product

Resources

About