Design optimization of zero power wake-up receiver in Power line communication

Golchin, Parian; Tosato, Pietro; Brunelli, Davide

doi:10.1109/speedam.2016.7526028

Cited by 5 publications

(6 citation statements)

References 16 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…This permits the modem and the attached load, which is the street lights, to persist into a deep sleep and only wakes up after collecting a signal. Some of passive wake up proposed pro-tocols in [193] and [194] banish energy inadequacy by eliminating idle listening while the machines are on stand-by.…”

Section: Smart Gridmentioning

confidence: 99%

An overview on low energy wake-up radio technology: Active and passive circuits associated with MAC and routing protocols

Zaraket¹,

Murad²,

Yazdani³

et al. 2021

Journal of Network and Computer Applications

View full text Add to dashboard Cite

Section: Smart Gridmentioning

confidence: 99%

An overview on low energy wake-up radio technology: Active and passive circuits associated with MAC and routing protocols

Zaraket¹,

Murad²,

Yazdani³

et al. 2021

Journal of Network and Computer Applications

View full text Add to dashboard Cite

“…Among these, power line communications (PLC) is a straightforward non-wireless choice. Several wake-up mechanisms that share similar medium, requirements, and protocols have been already proposed [176], [177].…”

Section: ) Matching Prototypesmentioning

confidence: 99%

“…1) Matching Prototypes: Micro-grid communication often includes heterogeneous technologies. Some of the prototypes that suit smart grid requirements are presented in [36], [67], and [178], while non-RF wakeup circuits such as those in [176] and [177] also exists even if with features tailored for cable communication [177].…”

Section: ) Matching Prototypesmentioning

confidence: 99%

Ultra Low Power Wake-Up Radios: A Hardware and Networking Survey

Piyare

Murphy

Király

et al. 2017

IEEE Commun. Surv. Tutorials

Self Cite

217

160

View full text Add to dashboard Cite

In wireless environments, transmission and 1 reception costs dominate system power consumption, motivating 2 research effort on new technologies capable of reducing the 3 footprint of the radio, paving the way for the Internet of 4 Things. The most important challenge is to reduce power 5 consumption when receivers are idle, the so called idle-listening 6 cost. One approach proposes switching off the main receiver, 7 then introduces new wake-up circuitry capable of detecting 8 an incoming transmission, optionally discriminating the packet 9 destination using addressing, then switching on the main radio 10 only when required. This wake-up receiver technology represents 11 the ultimate frontier in low power radio communication. In 12 this paper, we present a comprehensive literature review of 13 the research progress in wake-up radio (WuR) hardware and 14 relevant networking software. First, we present an overview of 15 the WuR system architecture, including challenges to hardware 16 design and a comparison of solutions presented throughout the 17 last decade. Next, we present various medium access control and 18 routing protocols as well as diverse ways to exploit WuRs, both 19 as an extension of pre-existing systems and as a new concept to 20 manage low-power networking.

show abstract

“…However, the energy efficiency of this method is reduced in periodic communication scenarios such as smart street lighting. Passive wake-up protocols proposed in [118,119] eliminate this energy inefficiency by removing idle listening when the devices are on stand-by. Figure 10 shows a graphical representation of smart grid application in passive street light PLC.…”

Section: Key Application Areas For Passive Wake-up Radiomentioning

confidence: 99%

Advances and Opportunities in Passive Wake-Up Radios with Wireless Energy Harvesting for the Internet of Things Applications

Bello

Zeng

Nordin

et al. 2019

Sensors

View full text Add to dashboard Cite

Wake-up radio is a promising approach to mitigate the problem of idle listening, which incurs additional power consumption for the Internet of Things (IoT) wireless transmission. Radio frequency (RF) energy harvesting technique allows the wake-up radio to remain in a deep sleep and only become active after receiving an external RF signal to ‘wake-up’ the radio, thus eliminating necessary hardware and signal processing to perform idle listening, resulting in higher energy efficiency. This review paper focuses on cross-layer; physical and media access control (PHY and MAC) approaches on passive wake-up radio based on the previous works from the literature. First, an explanation of the circuit design and system architecture of the passive wake-up radios is presented. Afterward, the previous works on RF energy harvesting techniques and the existing passive wake-up radio hardware architectures available in the literature are surveyed and classified. An evaluation of the various MAC protocols utilized for the novel passive wake-up radio technologies is presented. Finally, the paper highlights the potential research opportunities and practical challenges related to the practical implementation of wake-up technology for future IoT applications.

show abstract

Design optimization of zero power wake-up receiver in Power line communication

Cited by 5 publications

References 16 publications

An overview on low energy wake-up radio technology: Active and passive circuits associated with MAC and routing protocols

An overview on low energy wake-up radio technology: Active and passive circuits associated with MAC and routing protocols

Ultra Low Power Wake-Up Radios: A Hardware and Networking Survey

Advances and Opportunities in Passive Wake-Up Radios with Wireless Energy Harvesting for the Internet of Things Applications

Contact Info

Product

Resources

About