Closure to “Base Stability of Deep Excavation in Anisotropic Soft Clay” by S. F. Su, H. J. Liao, and Y. H. Lin

Su, S. F.; Liao, Hung‐Jiun; Lin, Yujian

doi:10.1061/(asce)1090-0241(2000)126:8(760)

Cited by 23 publications

(38 citation statements)

References 3 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The phosphate based conversion coatings have been widely used to modify the corrosion resistance of the metal substrate and provide good adhesion of the organic coating on the steel substrate. It has been shown that surface treatment of the steel sample by the zinc phosphate conversion layer can result in significant increase of the epoxy coating adhesion properties and corrosion resistance [29,30].…”

Section: Introductionmentioning

confidence: 99%

Improved performance of cerium conversion coatings on steel with zinc phosphate post-treatment

Ramezanzadeh

Vakili

Amini

2015

Journal of Industrial and Engineering Chemistry

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 99%

Improved performance of cerium conversion coatings on steel with zinc phosphate post-treatment

Ramezanzadeh

Vakili

Amini

2015

Journal of Industrial and Engineering Chemistry

View full text Add to dashboard Cite

“…The mechanisms of nano Ag against Gram-positive and Gram-negative bacteria are different. The antibacterial mechanisms of nano Ag from research achievements include five aspects: effect on living environments of bacteria, destruction of cell wall and cell membrane of bacteria, inhibition of DNA replication, suppression of respiration of enzyme, and inhibition of activity of other enzymes [33][34][35][36]. It has been widely accepted that a high content of nano Ag can easily adsorb onto the bacterial cell surface, pass through the microbial body, then convert to silver ions (Ag + ) in cytoplasm to damage the intracellular structure [37,38].…”

Section: Antibacterial Activitymentioning

confidence: 99%

Fabrication and characterization of waterborne polyurethane/silver nanocomposite foams

et al. 2018

View full text Add to dashboard Cite

Nowadays the waterborne polyurethane (WPU) is a newly developed polymer foam material as a replacement for conventional organic solvent‐based polyurethane (PU). Nevertheless, the WPU foams exhibit some drawbacks such as inferior mechanical strength, low thermal and dimensional stability, which inhibits its large‐scale application at present. So a series of novel WPU/silver nanocomposite foams was successfully prepared by mechanical foaming method. The effect of silver nanoparticles (nano Ag) content on the morphology, thermal behavior, air permeability, water vapor transmission rate (WVT), mechanical, and antibacterial properties of WPU/Ag nanocomposite foams were systematically investigated. The results revealed that the nano Ag were uniformly dispersed in WPU matrix and facilitated cell growth, leading to enhanced mean pore size, thermal stability, air permeability, and WVT value of nanocomposite foams. About 122% improvement in the air permeability and 28% improvement in the WVT value were obtained when the nano Ag content extended from 0 to 4 wt%. It was found that the nano Ag content had great influence on tensile strength and elongation at break. When nano Ag content was 2 wt%, the nanocomposite foam exhibited the maximum tensile strength value of 1.26 MPa. Moreover, because of the addition of nano Ag, the nanocomposite foam showed bacteriostatic rate of 98.23% and 97.38% against Escherichia coli and Staphylococcus aureus, respectively. POLYM. COMPOS., 40:1492–1498, 2019. © 2018 Society of Plastics Engineers

show abstract

“…Moreover, as the development of active matrix organic LEDs (AMOLEDs), LCD can be replaced with blue OLEDs as excitation light. In comparison with LCD panel, blue OLEDs (BOLEDs) have several obvious superiorities such as self-emitting structure, thin thickness, wide viewing angle, high contrast ratio, and short response time [10,11] .…”

Section: Introductionmentioning

confidence: 99%

P‐9.9: Research on The New Display Technology ‐ Inkjet‐Printed Quantum Dot Display with Blue OLEDs

Li¹,

Hu²,

Peng³

et al. 2019

Symp Digest of Tech Papers

View full text Add to dashboard Cite

Colloidal quantum dot (QD) display is expected to be promising technology for the next generation display due to the advantages of QDs. In this work, we designed and fabricated 6.6 inch inkjet printed red QD‐OLED device, 3‐stack blue OLEDs (BOLEDs) with top‐emission structure acted as backlight. Red QD layer acted as converted materials, which exhbitted high quantum efficiency, high luminance, high color purity and improved wide viewing angle of output emission. We believe that inkjet‐printed QD color convert layer with AMOLEDs would be promising candidate for next generation display in the near future.

show abstract

Closure to “Base Stability of Deep Excavation in Anisotropic Soft Clay” by S. F. Su, H. J. Liao, and Y. H. Lin

Cited by 23 publications

References 3 publications

Improved performance of cerium conversion coatings on steel with zinc phosphate post-treatment

Improved performance of cerium conversion coatings on steel with zinc phosphate post-treatment

Fabrication and characterization of waterborne polyurethane/silver nanocomposite foams

P‐9.9: Research on The New Display Technology ‐ Inkjet‐Printed Quantum Dot Display with Blue OLEDs

Contact Info

Product

Resources

About