Analisys of Corrosion Behavior of Ti-15Mo Alloys

Nava-Dino, C.G.; Bautista-Margulis, R.G.; Neri-Flores, M.A.; Orozco-Carmona, M. V.; Torre, S.D. De la; Chacón-Nava, J.G.; Martínez‐Villafañe, A.

doi:10.1016/s1452-3981(23)19535-6

Cited by 5 publications

(1 citation statement)

References 20 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Also, it is cheaper than other β -stabilizing elements, so it offers significant economic savings [8–11]. In addition, this alloy has a lower elastic modulus despite its good corrosion resistance [9–15]. It is important to note that Mo, as an essential trace element in human nutrition, is useful in regulating the pH balance in the body [16].…”

Section: Introductionmentioning

confidence: 99%

Investigation of mechanical properties and microstructure of Ti-15% Mo alloy produced by mechanical alloying and sintering with SPS (MA-SPS)

et al. 2022

View full text Add to dashboard Cite

The goal of this study was to investigate the mechanical properties and microstructure of Ti-15% Mo alloy fabricated using the mechanical alloying and spark plasma sintering (MA-SPS) method. Accordingly, Ti and Mo powders were milled for different times, including 5, 15, 25, 35, and 45 h, and the SPS technique for sintering under a pressure of 25 MPa at 1100°C was used. The X-ray diffraction (XRD) analysis, optical and electron microscopy (SEM), hardness measurements, and compression testing were used to study the phases formed, the morphology of powders, microstructure, and mechanical properties of the as-prepared samples, respectively. The results revealed that owing to increasing the mechanical milling time, the percentage of the beta phase formed was higher, and in addition, it influenced the microstructure and mechanical properties of the samples fabricated after the sintering process.

show abstract

Section: Introductionmentioning

confidence: 99%

Investigation of mechanical properties and microstructure of Ti-15% Mo alloy produced by mechanical alloying and sintering with SPS (MA-SPS)

et al. 2022

View full text Add to dashboard Cite

show abstract

Long-term corrosion behavior and biocompatibility testing of titanium-based alloy covered with nano-crystalline hydroxyapatite

Popa

Vasilescu

Drob

et al. 2014

Materials and Corrosion

View full text Add to dashboard Cite

In this paper, we applied on the surface of the new Ti-20Nb-10Zr-5Ta alloy nano-crystalline hydroxyapatite (HA) coating by the method of the chemical deposition in a solution supersaturated with Ca 2þ and PO 3À 4 ions. The composition and crystallinity of the obtained coating was determined by X-ray diffraction, micro-Raman, infrared, and energy dispersive X-ray spectroscopies and its morphology and porosity by scanning electron microscopy. The coating long-term corrosion behavior for 3000 soaking hours in simulated human fluids (Ringer's solutions of different pH values) was studied by cyclic potentiodynamic and linear polarization, electrochemical impedance spectroscopy and monitoring of the open circuit potentials and corresponding open circuit potential gradient due to the pH non-uniformity of the biofluid. Also, the coating biocompatibility was performed by cells (human osteoblast -HOS and human immortalized pulmonary fibroblast -Wi-38) adhesion and proliferation testing in the HA coated bioalloy extract compared to respective effects of the uncoated bioalloy extract. The initial HA nano-coating promoted the deposition of new HA layers, thickening itself and showing its ability to induce the formation of this main inorganic component of the human bone, therefore denoting bioactivity of the HA nano-coated alloy.

show abstract

Electrochemical Noise Study of Ni-Mo Alloys Fabricated by Mechanical Alloying and Densified by Spark Plasma Sintering

Almeraya‐Calderón

Bautista-Margulis

Nava-Dino

et al. 2012

International Journal of Electrochemical Science

View full text Add to dashboard Cite

Analisys of Corrosion Behavior of Ti-15Mo Alloys

Cited by 5 publications

References 20 publications

Investigation of mechanical properties and microstructure of Ti-15% Mo alloy produced by mechanical alloying and sintering with SPS (MA-SPS)

Investigation of mechanical properties and microstructure of Ti-15% Mo alloy produced by mechanical alloying and sintering with SPS (MA-SPS)

Long-term corrosion behavior and biocompatibility testing of titanium-based alloy covered with nano-crystalline hydroxyapatite

Electrochemical Noise Study of Ni-Mo Alloys Fabricated by Mechanical Alloying and Densified by Spark Plasma Sintering

Contact Info

Product

Resources

About