По расплавной технологии получены образцы нанокомпозитов на основе полиметилметакрилата и полистирола с добавлением наночастиц диоксида кремния, поверхностно модифицированных силазанами. Исследовано влияние этих наночастиц на вязкоупругие свойства нанокомпозитов с помощью динамического механического анализа и показано, что введение 20 mass.% SiO 2 приводит к повышению в среднем на 30% модуля упругости нанокомпозитов при изгибе. DOI: 10.21883/JTF.2017.02.44136.1963 Введение Полимерные нанокомпозитные материалы (ПНК) на-ходят в настоящее время все более широкое применение в таких областях как авиа-и автомобилестроение, где подвергаются разнообразным динамическим нагрузкам. При этом если для измерения статических механических параметров материалов разработаны стандартные проце-дуры измерений (ISO, ANSI и т. д.), то общепринятых методов измерения динамических модулей упругости пока не существует. Помимо того что значения модулей упругости сильно зависят от способа получения полиме-ра, метода измерений, часто эти характеристики изме-ряются с большими погрешностями. В особенности это касается модулей упругости третьего порядка, ошибка измерения которых может составлять десятки и даже сотни процентов.Как известно, многие аморфные полимеры, такие, например, как полистирол (ПС), полиметилметакрилат (ПММА), поликарбонат (ПК) в стеклообразном со-стоянии обладают выраженными нелинейно упругими свойствами. Можно предположить, что нанокомпозиты на их основе также будут демонстрировать нелинейно упругие свойства, но при этом иметь отличные от матрицы физико-механические параметры. Знание нели-нейно упругих свойств этих полимеров имеет большое значение, в частности, для формирования в них объ-емных уединенных волн (солитонов) деформации [1]. Нами ранее было показано (см. [1,2] и приведенные там ссылки), что возможность формирования в материале нелинейной уединенной волны определяется комбина-цией упругих модулей второго и третьего порядков материала, геометрическими параметрами волновода и характеристиками возбуждающего импульса (ударной волны). Таким образом, информация об упругих харак-теристиках материала имеет решающее значение при определении возможности формирования в нем соли-тона деформации. Отметим, что солитоны деформации могут переносить упругую энергию на большие расстоя-ния почти без потерь [2,3], и возможность их генерации в различных конструкциях в процессе эксплуатации, в особенности в таких жизненно важных областях, как авиакосмическая техника, или транспортировка нефти и газа, необходимо принимать во внимание.Технология получения ПНК нацелена на создание материалов, в которых путем направленного сочета-ния компонентов (полимерной матрицы и наполните-лей различной природы) достигаются заранее заданные свойства. Такой способ получения ПНК дает возмож-ность создавать принципиально новые и разнообразные конструкции, способствующие увеличению прочности, снижению массы, улучшению физических свойств изде-лий [4][5][6][7].Как известно, создание эффективных ПНК на основе термопластов возможно с использованием различных...
Regularities of statistical distributions of a complex of mechanical properties, including the module of elasticity (E), strength () and strain at break (b), high-strength industrial oriented polypropylene (PP) fibers have been analyzed using the Weibull and Gauss models based on large a wide array of measurements (50 identical samples in each series). The values of the statistical Weibull modulus (m) - a parameter characterizing the scatter of the measured values of the data arrays of E, and b – have been estimated for the PP samples of two types: single fibers (monofilaments) and multifilament fibers consisting from several hundred single fibers. For the PP multifilament fibers, a more correct description of the distributions of E, and b has been received both in the framework of the normal distribution (Gaussian distribution) and in the framework of the Weibull distribution in comparison with the description of such distributions for the PP monofilaments. The influence of the polymer chain conformation on the regularities of the statistical distributions of E, and b for the high-strength oriented polymeric materials with different chemical chain structures and the correctness of their descriptions in the framework of the Gauss and Weibull models have been analyzed. For this purpose, the values of m calculated in this work for PP with a helical chain conformation have been compared with the values of m determined by us earlier for ultra-high molecular weight polyethylene and polyamide-6 with the chain conformations in the form of an in-plane trans-zigzag.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.