Carbonate rock reservoirs comprise approximately 60% of the world's oil and gas reserves. Complex flow mechanisms and strong adsorption of crude oil on carbonate formation surfaces can reduce hydrocarbon recovery of an oil-wet carbonate reservoir to as low as 10%. Low salinity waterflooding (LSW) has been confirmed as a promising technique to improve the oil recovery factor. However, the principal mechanism underpinning this recovery method is not fully understood, which poses a challenge toward designing the optimal salinity and ionic composition of any injection solution. In general, it is believed that there is more than one mechanism involved in LSW of carbonates; even though wettability alteration toward a more desirable state for oil to be recovered could be the main cause during LSW, how this alteration happens is still the subject of debate. This paper reviews different working conditions of LSW, previous studies, and field observations, alongside the proposed interfacial mechanisms which affect the colloidal interactions at oil-rock-brine interfaces. This paper provides a comprehensive review of studies on LSW in carbonate formation and further analyzes the latest achievements of LSW application in carbonates, which helps to better understand the challenges involved in these complicated multicomponent systems and potentially benefits the oil production industry.

The frictional properties of poly(2-(methacryloyloxy)ethylphosphorylcholine) (PMPC) brushes grown from planar silicon surfaces by atom transfer radical polymerization (ATRP) have been characterized using in situ friction force microscopy (FFM). The dry thicknesses of the PMPC brushes ranged from 20 to 421 nm. For brush layers with dry thicknesses greater than ca. 100 nm, the coefficient of friction decreased with increasing film thickness. For shorter brushes, the coefficient of friction varied little with brush thickness. We hypothesize that the amount of bound solvent increases as the brush length increases, causing the osmotic pressure to increase and yielding a reduced tendency for the brush layer to deform under applied load. A comparison of the force-displacement plots acquired for various PMPC brushes under water supports this hypothesis, since a greater repulsive force is measured for thicker brushes. FFM was also used to investigate the well-known co-nonsolvency behavior exhibited by PMPC chains. For a PMPC brush layer of 307 nm dry thickness, the friction force was determined as a function of the volume fraction of alcohol in alcohol/water mixtures. Unlike a previous macroscopic study, a significant increase in the coefficient of friction was observed for ethanol/water mixtures at a volume fraction of 90%. This is attributed to brush collapse due to co-nonsolvency, leading to loss of hydration of the brush chains and hence substantially reduced lubrication. Force measurements normal to the surface indicate much greater hysteresis between approaching and retraction curves under co-nonsolvency conditions. However, no such effect was observed for 2-propanol/water and methanol/water mixtures over a wide range of volume fractions, in agreement with recent ellipsometric studies of PMPC brushes.

A quantitative investigation of the responses of surface-grown biocompatible brushes of poly(2-(methacryloyloxy)ethyl phosphorylcholine) (PMPC) to different types of salt has been carried out using ellipsometry, quartz crystal microbalance (QCM) measurements, and friction force microscopy. Both cations and anions of varying valency over a wide range of concentrations were examined. Ellipsometry shows that the height of the brushes is largely independent of the ionic strength, confirming that the degree of swelling of the polymer is independent of the ionic character of the medium. In contrast, QCM measurements reveal significant changes in mass and dissipation to the PMPC brush layer, suggesting that ions bind to phosphorylcholine (PC) groups in PMPC molecules, which results in changes in the stiffness of the brush layer, and the binding affinity varies with salt type. Nanotribological measurements made using friction force microscopy show that the coefficient of friction decreases with increasing ionic strength for a variety of salts, supporting the conclusion drawn from QCM measurements. It is proposed that the binding of ions to the PMPC molecules does not change their hydration state, and hence the height of the surface-grown polymeric brushes. However, the balance of the intra- and intermolecular interactions is strongly dependent upon the ionic character of the medium between the hydrated chains, modulating the interactions between the zwitterionic PC pendant groups and, consequently, the stiffness of the PMPC molecules in the brush layer.

Lubricant additives, based on inorganic nanoparticles coated with organic outer layer, can reduce wear and increase load-carrying capacity of base oil remarkably, indicating the great potential of hybrid nanoparticles as anti-wear and extreme-pressure additives with excellent levels of performance. The organic part in the hybrid materials improves their flexibility and stability, while the inorganic part is responsible for hardness. The relationship between the design parameters of the organic coatings, such as molecular architecture and the lubrication performance, however, remains to be fully elucidated. A survey of current understanding of hybrid nanoparticles as lubricant additives is presented in this review.

The influence of different types of salts (NaCl, CaCl 2 , MgCl 2 , NaHCO 3 , and Na 2 SO 4 ) on the surface characteristics of unconditioned calcite and dolomite particles, and conditioned with stearic acid, was investigated. This study used zeta potential measurements to gain fundamental understanding of physico-chemical mechanisms involved in surface charge modification of carbonate minerals in the presence of diluted salt solutions. By increasing the salt concentration of divalent cationic salt solution (CaCl 2 and MgCl 2 ), the zeta potential of calcite particles was altered, resulting in charge reversal from negative to positive, while dolomite particles maintained positive zeta potential. This is due to the adsorption of potential-determining cations (Ca 2 + and Mg 2 + ), and consequent changes in the structure of the diffuse layer, predominantly driven by coulombic interactions. On the other hand, chemical adsorption of potential-determining anions (HCO 3 - and SO 4 2 - ) maintained the negative zeta potential of carbonate surfaces and increased its magnitude up to 10 mM, before decreasing at higher salt concentrations. Physisorption of stearic acid molecules on the calcite and dolomite surfaces changed the zeta potential to more negative values in all solutions. It is argued that divalent cations (Ca 2 + and Mg 2 + ) would result in positive and neutral complexes with stearic acid molecules, which may result in strongly bound stearic acid films, whereas ions resulting in negative mineral surface charges (SO 4 2 - and HCO 3 - ) will cause stearic acid films to be loosely bound to the carbonate mineral surfaces. The suggested mechanism for surface charge modification of carbonates, in the presence of different ions, is changes in both distribution of ions in the diffuse layer and its structure as a result of ion adsorption to the crystal lattice by having a positive contribution to the disjoining pressures when changing electrolyte concentration. This work extends the current knowledge base for dynamic water injection design by determining the effect of salt concentration on surface electrostatics.