This paper presents a methodology for the sizing and synthesis of power generation and distribution (PG&D) subsystems. The PG&D subsystem models developed in a previous work done by the authors were applied within a parallel hybrid electric propulsion architecture using the Dornier 328 as the baseline aircraft. The hybridization took place only during the cruise segment. Analyses were performed in Pacelab SysArc, a system architecture design tool, to assess the impact of different hybrid electric propulsion architectures and changing PG&D subsystem characteristics at aircraft and mission levels. To this end, sensitivity analysis was conducted to reveal the sensitivity to the subsystem level characteristics. Moreover, six different architectures were compared in terms of their mission level performance. These architectures included the PG&D subsystems with current state of the art technology, NASA 15-year technology goals and a more advanced battery technology. Although neither the current state of the art PG&D subsystems nor NASA 15-year technology goals were advanced enough to match the design range requirement of the baseline aircraft, some of the competing architectures met the practical range target while enjoying substantial amount of fuel reductions. Finally, it was observed that in order to reach a break-even point in terms of the design mission range, a battery specific energy of 5 kWh/kg was necessary for a 50% level of hybridization during cruise. In this work the Dornier 328 was used as a testbed, however the methodology can be generalized for all parallel hybrid electric propulsion applications.
The ongoing efforts to reduce aviation related greenhouse gas emissions and fuel burn have led to advancements in power generation and distribution (PG&D) subsystem technology. Due to the absence of historical data, PG&D subsystem models must be created from first-order analysis without compromising crucial information on their characteristics. This paper demonstrates the development of parametric, physics-based subsystem models such as battery, electric motor, power distribution and management system, and propeller speed reduction unit for rapid and low-cost sizing, simulation and analysis at early design stages. A special focus was put on rechargeable battery technology and implementing a dynamic (rather than steady-state) discharge behavior into the propulsion architecture. A methodology to integrate the developed subsystem models was presented. A sample application was also provided to demonstrate the combined capabilities of the models. To this end, the models were applied within a sample parallel hybrid electric architecture using Dornier 328 as a test bed. The subsystem behaviors under varying power requirements were then analyzed. Finally, the importance of having more dimensionality at the subsystem level at early design stages was highlighted by comparing the results of two different architectural choices.
This investigation surveyed the potential and established outcomes for future 19-passenger fixed-wing commuter transport aircraft concepts employing battery-based Voltaic-Joule/Brayton motive power systems with no additional electrical energy drawn from generators mechanically coupled to thermal engines. The morphological approach was that of a tri-prop (two on-wing podded turbo-props and one aft-fuselage mounted electric motor configured as a pusher-on-pylon installation). A Battery System-level Gravimetric Specific Energy (referred to as “battery energy density”) of at least 500 Wh/kg yielded 39%, 25% and 10% block fuel reductions for 150-nm (Design Service Goal), 430-nm (85th percentile) and 700-nm (maximum range) stage lengths, respectively. All quoted comparisons are against a suitably projected turbo-prop only year-2030 aircraft. In contrast to the reference Beech 1900D, block fuel reductions of up to 44-49% were predicted, which could facilitate a significantly lower deficit in relation to the Advisory Council for Aviation Research and Innovation in Europe (ACARE) Strategic Research and Innovation Agenda (STRIA) 55% target for year 2030. This investigation also indicated that, in the future, suitably flexible hybrid-electric architectures could be fashioned allowing possibility for the aircraft to complete any required city-pair operations (within the legitimate payload-range working capacity) irrespective of exchangeable batteries being available at a given station. Finally, it was also established, assuming such a tri-prop morphology, Normal conducting machines delivering maximum shaft power output of 1.1 MW would be required.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.