Abstract. High power impulse magnetron sputtering (HiPIMS) plasmas generate energetic metal ions at the substrate as a major difference to conventional direct current magnetron sputtering (dcMS). The origin of these very energetic ions in HiPIMS is still an open issue, which is unraveled by using two fast diagnostics: time resolved mass spectrometry with a temporal resolution of 2 µs and phase resolved optical emission spectroscopy with a temporal resolution of 1 µs. A power scan from dcMS-like to HiPIMS plasmas was performed, with a 2-inch magnetron and a titanium target as sputter source and argon as working gas. Clear differences in the transport as well in the energetic properties of Ar + , Ar 2+ , Ti + and Ti 2+ were observed. For discharges with highest peak power densities a high energetic group of Ti + and Ti 2+ could be identified with energies of approximately 25 eV and of 50 eV, respectively. A cold group of ions is always present. It is found that hot ions are observed only, when the plasma enters the spokes regime, which can be monitored by oscillations in the IV-characteristics in the MHz range that are picked up by the used VI-probes. These oscillations are correlated with the spokes phenomenon and are explained as an amplification of the Hall current inside the spokes as hot ionization zones. To explain the presence of energetic ions, we propose a double layer (DL) confining the hot plasma inside a spoke: if an atom becomes ionized inside the spokes region it is accelerated because of the DL to higher energies whereas its energy remains unchanged if it is ionized outside. In applying this DL model to our measurements the observed phenomena as well as several measurements from other groups can be explained. Only if spokes and a double layer are present the confined particles can gain enough energy to leave the magnetic trap. We conclude from our findings that the spoke phenomenon represents the essence of HiPIMS plasmas, explaining their good performance for material synthesis applications. ‡

The temporal distribution of the incident fluxes of argon and titanium ions on the substrate during an argon HiPIMS pulse to sputter titanium with pulse lengths between 50 to 400 µs and peak powers up to 6 kW are measured by energy-resolved ion mass spectrometry with a temporal resolution of 2 µs. The data are correlated with time-resolved growth rates and with phase-resolved optical emission spectra. Four ion contributions impinging on the substrate at different times and energies are identified: (i) an initial argon ion burst after ignition, (ii) a titanium and argon ion flux in phase with the plasma current due to ionized neutrals in front of the target, (iii) a small energetic burst of ions after plasma shut off, and (iv) cold ions impinging on the substrate in the late afterglow showing a pronounced maximum in current. The last contribution originates from ions generated during the plasma current maximum at 50 µs after ignition in the magnetic trap in front of the target. They require long transport times of a few 100 µs to reach the substrate. All energy distributions can be very well fitted with a shifted Maxwellian indicating an efficient thermalization of the energetic species on their travel from target to substrate. The energy of titanium is higher than that of argon, because they originate from energetic neutrals of the sputter process. The determination of the temporal sequence of species, energies and fluxes in HiPIMS may lead to design rules for the targeted generation of these discharges and for synchronized biasing concepts to further improve the capabilities of high-power impulse magnetron sputtering (HiPIMS) processes.

High power impulse magnetron sputtering (HiPIMS) is a versatile technology to deposit thin films with superior properties. During HiPIMS, the power is applied in short pulses of the order of 100 μs at power densities of kW to a magnetron target creating a torus shaped dynamic high density plasma. This plasma torus is not homogeneous, but individual ionization zones become visible, which rotate along the torus with velocities of 10 km . Up to now, however, any direct measurement of the electron density inside these rotating ionization zones is missing. Here, we probe the electron density by measuring the target current locally by using small inserts embedded in an aluminium target facing the plasma torus. By applying simple sheath theory, a plasma density of the order of at the sheath edge can be inferred. The plasma density increases with increasing target current. In addition, the dynamics of the local target current variation is consistent with the dynamics of the traveling ionization zone causing a modulation of the local current density by 25%.

High power magnetron sputtering (HiPIMS) discharges generate ions with high kinetic energies in comparison to conventional dc magnetron sputtering. The peculiar shape of the ion energy distribution function (IEDF) is correlated to the formation of localized ionization zones (IZ) in the racetrack of a HiPIMS discharge, so called spokes. This is explained by a local maximum of the electrical potential inside these localized IZ. By using ion energy mass spectrometry, probe experiments and plasma spectroscopy the connection between IZ and IEDFs is evaluated with high temporal resolution. The data of a floating probe next to the target is used to directly monitor the movement of the spokes in the × E B direction. Chromium is used as target material, because the plasma undergoes a sequence from stochastic spoke formation, to regular spoke pattern rotating in the × E B direction to a homogeneous plasma torus with increasing plasma power. In particular, the analysis of the transition from the regular spoke pattern to the homogeneous plasma torus at very high plasma powers shows that the high energy part of the IEDF is not affected and only the low energy part is modified. Consequently, one could consider the homogenous plasma torus at very high plasma powers as a a single ionization zone localized over the complete torus, which is formed by merging individual spokes with increasing power. Details and consequences of that model are discussed.

Spokes, localised ionisation zones, are commonly observed in magnetron sputtering plasmas, appearing either with a triangular shape or with a diffuse shape, exhibiting self-organisation patterns. In this paper, we investigate the spoke properties (shape and emission) in a high power impulse magnetron sputtering (HiPIMS) discharge when reactive gas (N2 or O2) is added to the Ar gas, for three target materials; Al, Cr, and Ti. Peak discharge current and total pressure were kept constant, and the discharge voltage and mass flow ratios of Ar and the reactive gas were adjusted. The variation of the discharge voltage is used as an indication of a change of the secondary electron yield. The optical emission spectroscopy data demonstrate that by addition of reactive gas, the HiPIMS plasma exhibits a transition from a metal dominated plasma to the plasma dominated by Ar ions and, at high reactive gas partial pressures, to the plasma dominated by reactive gas ions. For all investigated materials, the spoke shape changed to the diffuse spoke shape in the poisoned mode. The change from the metal to the reactive gas dominated plasma and increase in the secondary electron production observed as the decrease of the discharge voltage corroborate our model of the spoke, where the diffuse spoke appears when the plasma is dominated by species capable of generating secondary electrons from the target. Behaviour of the discharge voltage and maximum plasma emission is strongly dependant on the target/reactive gas combination and does not fully match the behaviour observed in DC magnetron sputtering.