No abstract

Treatment of common pathologies of the shoulder complex, such as rheumatoid arthritis and osteoporosis, is usually performed by total shoulder arthroplasty (TSA). Survival of the glenoid component is still a problem in TSA, whereas the humeral component is rarely subject to failure. To set up a finite element analysis (FEA) for simulation of a TSA in order to gain insight into the mechanical behaviour of a glenoid implant, the modelling procedure and the application of boundary conditions are of major importance because the computed result strongly depends upon the accuracy and sense of realism of the model. The goal of this study was to show the influence on glenoid stress distribution of a patient-specific bone density distribution compared with a homogenous bone density distribution for the purpose of generating a valid model in future FEA studies of the shoulder complex. Detailed information on the integration of bone density properties using existing numerical models as well as the applied boundary conditions is provided. A novel approach involving statistical analysis of values derived from an FEA is demonstrated using a cumulative distribution function. The results show well the mechanically superior behaviour of a realistic bone density distribution and therefore emphasise the necessity for patient-specific simulations in biomechanical and medical simulations.

This study investigates the mechanical behaviour of keeled and pegged implant designs used in shoulder arthroplasty for the first time using multiple 3D models. Thus, this study should provide valuable insights into the preferable use of either of these two controversial implant designs. Three-dimensional models of a scapula were derived from the CT scans of five patients, and an inter-patient-specific finite element analysis with special attention to bone density and boundary conditions was carried out. A distinct decrease in the investigated parameters was evident with the pegged implant in all of the patients, specifically for the implant and the bone cement. The relevance of the stress reduction within the bone is minor, whereas the reduction in the stress of the bone cement contributes to an increase in the bone cement survival. The particular construction of the pegged implant provides better stability and therefore supports bone ingrowth. The large variations between the patients show the necessity of patient-specific simulations and the use of multiple models to derive valuable results. In the conducted inter-patient-specific FEA, the pegged glenoid implants were found to exhibit superior behaviour compared with keeled implants. The results confirm the general clinical findings and demonstrate the FEA as a valuable tool in prosthetic and orthopaedic problems.

Purpose (1) To determine applied patellar drilling techniques for medial patellofemoral ligament (MPFL) reconstruction among members of the International Patellofemoral Study Group (IPSG) and (2) to evaluate the risk of patellar fracture for various patellar bone tunnel locations based on a inite element analysis (FEA) model. Methods In the irst part of the study, an online survey on current MPFL reconstruction techniques was conducted among members of the IPSG. In the second part of the study, a three-dimensional FEA model of a healthy knee joint was created using a computed tomography scan. Patient-speciic bone density was integrated into the patella, and cartilage of 3 mm thickness was modeled for the patellofemoral joint. According to the survey's results, two diferent types of patellar bone tunnels (bone socket and transpatellar bone tunnel) were simulated. The risk of patellar fracture was evaluated based on the fracture risk volume (FRV) obtained from the FEA. Results Finite element analysis revealed that subchondral bone socket tunnel placement is associated with the lowest FRV but increased with an anterior ofset (1-5 mm). Transpatellar bone tunnels violating the lateral or anterior cortex showed a higher FRV compared to bone socket, with the highest values observed when the anterior cortex was penetrated. Conclusion Violation of the anterior or lateral patellar cortex using transpatellar bone tunnels increased FRV compared to a subchondral patellar bone socket tunnel. In MPFL reconstruction, subchondral patellar bone socket tunnels should be considered for patellar graft ixation to avoid the risk of postoperative patellar fracture. Level of evidence Survey; Descriptive laboratory study/Level V.

Purpose: the aim of the computational 3D-finite element study is to evaluate the influence of an augmented sinus lift with additional inserted bone grafting. The bone graft block stabilizes the implant in conjunction with conventional bone augmentation. Two finite element models were applied: the real geometry based bone models and the simplified geometry models. The bone graft block was placed in three different positions. The implants were loaded first with an axial force and then with forces simulating laterotrusion and protrusion. This study examines whether the calculated stress behavior is symmetrical for both models. Having established a symmetry between the primary axis, the laterotrusion and protrusion behavior reduces calculation efforts, by simplifying the model. Material and Methods: a simplified U-shaped 3D finite element model of the molar region of the upper jaw and a more complex anatomical model of the left maxilla with less cortical bone were created. The bone graft block was placed in the maxillary sinus. Then the von Mises stress distribution was calculated and analyzed at three block positions: at contact with the sinus floor, in the middle of the implant helix and in the upper third of the implant. The two finite element models were then compared to simplify the modelling. Results: the position of the bone graft block significantly influences the magnitude of stress distribution. A bone graft block positioned in the upper third or middle of the implant reduces the quantity of stress compared to the reference model without a bone graft block. The low bone graft block position is clearly associated with lower stress distribution in compact bone. We registered no significant differences in stress in compact bone with regard to laterotrusion or protrusion. Conclusions: maximum values of von Mises stresses in compact bone can be reduced significantly by using a bone graft block. The reduction of stress is nearly the same for positions in the upper third and the middle of the implant. It is much more pronounced when the bone graft block is in the lower third of the implant near the sinus floor, which appeared to be the best position in the present study.