We present a method for synthesizing MoS(2)/Graphene hybrid heterostructures with a growth template of graphene-covered Cu foil. Compared to other recent reports, (1, 2) a much lower growth temperature of 400 °C is required for this procedure. The chemical vapor deposition of MoS(2) on the graphene surface gives rise to single crystalline hexagonal flakes with a typical lateral size ranging from several hundred nanometers to several micrometers. The precursor (ammonium thiomolybdate) together with solvent was transported to graphene surface by a carrier gas at room temperature, which was then followed by post annealing. At an elevated temperature, the precursor self-assembles to form MoS(2) flakes epitaxially on the graphene surface via thermal decomposition. With higher amount of precursor delivered onto the graphene surface, a continuous MoS(2) film on graphene can be obtained. This simple chemical vapor deposition method provides a unique approach for the synthesis of graphene heterostructures and surface functionalization of graphene. The synthesized two-dimensional MoS(2)/Graphene hybrids possess great potential toward the development of new optical and electronic devices as well as a wide variety of newly synthesizable compounds for catalysts.

The thinnest semiconductor, molybdenum disulfide (MoS2) monolayer, exhibits promising prospects in the applications of optoelectronics and valleytronics. A uniform and highly crystalline MoS2 monolayer in a large area is highly desirable for both fundamental studies and substantial applications. Here, utilizing various aromatic molecules as seeding promoters, a large-area, highly crystalline, and uniform MoS2 monolayer was achieved with chemical vapor deposition (CVD) at a relatively low growth temperature (650 °C). The dependence of the growth results on the seed concentration and on the use of different seeding promoters is further investigated. It is also found that an optimized concentration of seed molecules is helpful for the nucleation of the MoS2. The newly identified seed molecules can be easily deposited on various substrates and allows the direct growth of monolayer MoS2 on Au, hexagonal boron nitride (h-BN), and graphene to achieve various hybrid structures.

Recently, monolayers of layered transition metal dichalcogenides (LTMD), such as MX2 (M = Mo, W and X = S, Se), have been reported to exhibit significant spin-valley coupling and optoelectronic performances because of the unique structural symmetry and band structures. Monolayers in this class of materials offered a burgeoning field in fundamental physics, energy harvesting, electronics, and optoelectronics. However, most studies to date are hindered by great challenges on the synthesis and transfer of high-quality LTMD monolayers. Hence, a feasible synthetic process to overcome the challenges is essential. Here, we demonstrate the growth of high-quality MS2 (M = Mo, W) monolayers using ambient-pressure chemical vapor deposition (APCVD) with the seeding of perylene-3,4,9,10-tetracarboxylic acid tetrapotassium salt (PTAS). The growth of a MS2 monolayer is achieved on various surfaces with a significant flexibility to surface corrugation. Electronic transport and optical performances of the as-grown MS2 monolayers are comparable to those of exfoliated MS2 monolayers. We also demonstrate a robust technique in transferring the MS2 monolayer samples to diverse surfaces, which may stimulate the progress on the class of materials and open a new route toward the synthesis of various novel hybrid structures with LTMD monolayer and functional materials.

Realizing Raman enhancement on a flat surface has become increasingly attractive after the discovery of graphene-enhanced Raman scattering (GERS). Two-dimensional (2D) layered materials, exhibiting a flat surface without dangling bonds, were thought to be strong candidates for both fundamental studies of this Raman enhancement effect and its extension to meet practical applications requirements. Here, we study the Raman enhancement effect on graphene, hexagonal boron nitride (h-BN), and molybdenum disulfide (MoS2), by using the copper phthalocyanine (CuPc) molecule as a probe. This molecule can sit on these layered materials in a face-on configuration. However, it is found that the Raman enhancement effect, which is observable on graphene, hBN, and MoS2, has different enhancement factors for the different vibrational modes of CuPc, depending strongly on the surfaces. Higher-frequency phonon modes of CuPc (such as those at 1342, 1452, 1531 cm(-1)) are enhanced more strongly on graphene than that on h-BN, while the lower frequency phonon modes of CuPc (such as those at 682, 749, 1142, 1185 cm(-1)) are enhanced more strongly on h-BN than that on graphene. MoS2 demonstrated the weakest Raman enhancement effect as a substrate among these three 2D materials. These differences are attributed to the different enhancement mechanisms related to the different electronic properties and chemical bonds exhibited by the three substrates: (1) graphene is zero-gap semiconductor and has a nonpolar C-C bond, which induces charge transfer (2) h-BN is insulating and has a strong B-N bond, while (3) MoS2 is semiconducting with the sulfur atoms on the surface and has a polar covalent bond (Mo-S) with the polarity in the vertical direction to the surface. Therefore, the different Raman enhancement mechanisms differ for each material: (1) charge transfer may occur for graphene; (2) strong dipole-dipole coupling may occur for h-BN, and (3) both charge transfer and dipole-dipole coupling may occur, although weaker in magnitude, for MoS2. Consequently, this work studied the origin of the Raman enhancement (specifically, chemical enhancement) and identifies h-BN and MoS2 as two different types of 2D materials with potential for use as Raman enhancement substrates.

No abstract