ResumoO artigo apresenta uma proposta canadense de classificação de pilhas de estéril do ponto de vista da sua estabilidade física. O método baseia-se na avaliação ponderada e semiquantitativa de fatores-chave que podem afetar a estabilidade. Seu resultado permite atribuir uma determinada classe à pilha de acordo com o potencial de instabilidade. Essas classes definem um nível de esforço recomendado para investigação, projeto, construção e monitoramento da pilha. Para a verificação da eficácia do sistema de classificação, foi realizado um estudo de caso diante da realidade da mineração de ferro, na cidade de Nova Lima, Minas Gerais. A execução desse trabalho envolveu uma pesquisa documental e um posterior trabalho de campo, a fim de se aplicar, as informações coletadas sobre as pilhas no sistema de classificação.O trabalho mostra, também, inovações introduzidas pelos autores sobre o uso do sistema de classificação como meio de atestar a qualidade do manejo das pilhas e de identificar condicionantes de um projeto. O sistema de classificação mostrou que se trata de uma ferramenta muito útil, tanto no planejamento, como também na avaliação de todas as fases da vida de uma pilha.Palavras-chave: Pilha de estéril, classificação, estabilidade, mineração de ferro. Abstract In this paper a Canadian proposal for waste dumps classification according to their physical stability is presented. The method is based on a semi-quantitative evaluation of key factors affecting the stability of a waste dump
Uma estrada de mina foi dimensionada com materiais típicos ocorrentes em mineração de minério de ferro no Brasil, utilizando-se os métodos empíricos CBR e DNER. Através do programa de dimensionamento estrutural mecanístico-empírico ELSYM5, compararam-se os resultados obtidos pelos métodos anteriores e propôs-se a otimização do dimensionamento feito pelo método DNER. Os resultados mostram que a espessura total do pavimento calculada pelos dois métodos é, basicamente, a mesma, sendo que a espessura da camada de base pelo método DNER é superior à obtida pelo CBR, enquanto o oposto ocorre com a sub-base. Ambos os dimensionamentos mostram, através da aplicação do software ELSYM5, que não são os mais apropriados, visto que a deformação de algumas camadas, principalmente no caso CBR, está acima do limite aceitável de 2000 µε. Através da variação da espessura das camadas, obteve-se um dimensionamento adequado, que levou à redução da espessura da camada total do pavimento de 1,97 m para 1,40 m. A redução da deformação das camadas, em que se variou o módulo de elasticidade, demonstra a importância da realização de ensaios de caracterização física dos materiais.
Herein, three-dimensional analyses of large strain consolidation applied to tailings disposal in mining pits is studied. The main goal is to estimate filling time and, accordingly, the capacity of the pit. Other useful results, such as dry density profiles and water pore pressure generation are also obtained. Two different slimes from the iron ore beneficiation are considered: a low plastic silt-clay material, and a 10 times more permeable silt-like soil. The consolidation constitutive relationships were obtained by performing HCT tests (Hydraulic Consolidation Test). The analyses were carried out using an algorithm that produces approximate solutions of the three-dimensional analysis using the computer program CONDES0. Two types of analyses were performed limiting the exact solution, one called upper bound and the other, lower bound. For purposes of this study, sensitivity analyses were also performed, including "instantaneous" consolidation, double drainage, and varying tailings production. Simulations of the co-disposal of the two different slimes were also addressed, where simultaneous rising and sharing of the tailings during reservoir occupation were sought by trial and error. In addition, prediction of the deposit surface profile in the long-term run was included. It was obtained from the filling of the pit with the Slime 01 for the lower bound 1054 days and for the upper bound, 1219 days. By comparing the slimes, Slime 02 offers the greater capacity. In the scenario of co-disposition, Slime 01 occupies 43% of the area and Slime 02, 57% of the area of the pit. Having already analyzed scenarios with constant and variable production of Slime 01 a greater capacity of the pit was obtained for a constant production. Finally, there is a small difference in the pit capacity when the analyses are made considering the impermeable base and the permeable base.
An alternative method for quality control of earthworks in mining tailing dams is described in this article. It is composed by a penetrometer, known by the acronym DCP (Dynamic Cone Penetrometer), and is used primarily in road construction (quality assessment of pavement layers). With this apparatus, strength measurement of superficial layers of natural and compacted soils can be performed, including mine sand tailings, in a fast and efficient manner. The instrument was successfully used in the construction control of an iron ore mining tailings staged dam in the Quadrilatero Ferrifero, in Minas Gerais State, and the results showed distinctly effective densification of the embankment compacted layers, but with a sort of irregularity in their spatial distribution. In addition, field control using the traditional core-cutter method was also performed for comparison between both techniques.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.