This reportwas preparedas an account of work sponsored by an agency of the United States Govemment. Neither the United States Govemment nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercialproduct,process,or serviceby trade name, trademark,manufacturer,or otherwisedoes not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Govermnent or any agency thereof. The views and ophfions of authors expressed herein do not necessarily state or reflect those of the United States Govemment or any agency thereof. This report has been reproduceddirectly from the best available copy.
Second-generation Pressurized Fluidized Bed (PFB) combined cycles employ topping combustion to raise the turbine inlet temperature for enhanced cycle efficiency. This concept creates special combustion system requirements that are very different from requirements of conventional gas turbine systems. The topping combustor provides the means for achieving state-of-the-art turbine inlet temperatures and is the main contributor to enhanced plant performance. The objective of this program is to develop a topping combustor that provides low emissions, and is a durable, efficient device exhibiting stable combustion and manageable wall temperatures. The combustor will be required to burn a low-Btu Syngas under normal “coal-fired” conditions. However, for start-up and/or carbonizer outage, it may be necessary to fire a clean fuel, such as oil or natural gas. Prior testing has shown the Westinghouse Multi-Annular Swirl Burner (MASB) to have excellent potential for this application. Metal wall temperatures can be maintained at acceptable levels, even though most “cooling” is done by 1600°F vitiated air. Good pattern factors and combustion efficiencies have been obtained. Additionally, low conversion rates of fuel bound nitrogen to NOx have been demonstrated. This paper presents an update of the status of an ongoing topping combustor development and test program for application to “Second-Generation Pressurized Fluidized Bed Combined Cycles (PFBCC).” The program is sponsored by the Department of Energy’s Morgantown Energy Technology Center (DOE/METC) and will first be applied commercially into the Clean Coal Technology Round V Four Rivers Energy Modernization Project. Phase 1 of the program involved a conceptual and economic study (Robertson et al., 1988); Phase 2 addresses design and subscale testing of components; and Phase 3 will cover pilot plant testing of components integrated into one system.
A project team consisting of Foster Wheeler Development Corporation, Westinghouse Electric Corporation, Gilbert/Commonwealth and the Institute of Gas Technology, are developing a Second Generation Pressurized Fluidized Bed System. Foster Wheeler is developing a carbonizer (a partial gasifier) and a pressurized fluidized bed combustor. Both these units operate a nominal 1600°F (870°C) for optimal sulfur capture. Since this temperature is well below the current combustion turbine combustor outlet operating temperature of 2350°F (1290°C) to reach commercialization, a topping combustor and hot gas cleanup (HGCU) equipment must be developed. Westinghouse is participating in the development of the high temperature gas cleanup equipment and the topping combustor. This paper concentrates on the design and test of the topping combustor. The topping combustor in this cycle must utilize a low heating value syngas from the carbonizer at approximately 1600°F (870°C) and 150 to 210 psi (1.0 to 1.4 MPa). The syngas entering the topping combustor has been previously cleaned of particulates and alkali by the hot gas cleanup (HGCU) system. It also contains significant fuel bound nitrogen present as ammonia and other compounds. The fuel-bound nitrogen is significant because it will selectively convert to NOx if the fuel is burned under the highly oxidizing conditions of standard combustion turbine combustors. The fuel must be burned with the vitiated air from the pressurized fluidized bed combustor (PFBC). Oxidizer has been cleaned of particulates and alkali by HGCU system, and has also been partially depleted in oxygen. The 1600°F (870°C) oxidizer must also be utilized to cool the combustor as much as possible, though a small amount of compressor discharge air at a lower temperature 700°F (about 370°C) may be used. The application requirements indicate that a rich-quench-lean (RQL) combustor is necessary and the multi-annular swirl burner (MASB) was selected for further development. This paper provides an update on the development and testing of this MASB combustor. Additionally, Westinghouse has been conducting computational fluid dynamic (CFD) and chemical kinetic studies to assist in the design of the combustor and to help optimize the operation of the combustor. Results of these models are presented and compared to the test results.
Second-Generation Pressurized Fluidized Bed (PFB) combined cycles employ topping combustion to raise the turbine inlet temperature for enhanced cycle efficiency. This concept creates special combustion system requirements that are very different from requirements of conventional gas turbine systems. The topping combustor provides the means for achieving state-of-the-art turbine inlet temperatures and is the main contributor to enhanced plant performance. The objective of this program is to develop a topping combustor that provides low emissions, and is a durable, efficient device exhibiting stable combustion and manageable wall temperature. The combustor will be required to burn a low-Btu syngas under normal “coal-fired” conditions. However, for start-up and/or carbonizer outage, it may be necessary to fire a clean fuel, such as, oil or natural gas. Prior testing has shown the Westinghouse Multi-Annular Swirl Burner (MASB) to have excellent potential for this application. Metal wall temperatures can be maintained at acceptable levels, even though most “cooling” is done by 1600°F vitiated air. Good pattern factors and combustion efficiencies have been obtained. Additionally, low conversion rates of fuel bound nitrogen to NOx have been demonstrated. This paper presents an update of the status of an ongoing topping combustor development and test program for application to “Second Generation Pressurized Fluidized Bed Combined Cycles (PFBCC).” The program is sponsored by the Department of Energy’s Morgantown Energy Technology Center (DOE/METC) and will first be applied commercially into the Clean Coal Technology Round V Four Rivers Energy Modernization Project. Phase 1 of the program involved a conceptual and economic study (Robertson et al., 1988); Phase 2 addresses design and subscale testing of components; and Phase 3 will cover pilot plant testing of components integrated into one system.
This: report was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infiiage privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof. The views and ophions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof. This report has been reproduced directly from the best available copy. Available to DOE and DOE contractors from the Office of Scientific and Technical Ioformation, 175 Oak Ridge Turnpike, Oak Ridge, TN 37831; prices available at (615) 576-8401.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.