Magnetorheological (MR) materials are classified as smart materials that can alter their rheological features once exposed to peripheral magnetic fields. MR materials have been a standard and one of the primary smart materials for the last few decades due to their outstanding vibration control performance in adaptive sandwich structures and systems. This paper reviews the vibration suppression investigations of flexible constructions using MR elastomers (MREs). In relations of field-dependent controllability, physical features such as stiffness and the damping of different geometrical structures integrated with the core layer of MREs are explored. The veracity of the knowledge is discussed in this article, whereby sandwich structures with different MR treatment configurations are analyzed for free and forced vibration, MRE sandwich structures are analyzed for stability under different working conditions, and the optimal positions of fully and partially treated MRE sandwich structures for improved vibration control are identified. MR materials′ field-dependent stiffness and damping characteristics are also discussed in this article. A few of the most noteworthy research articles over the last several years have been summarized.
In this article a sandwich beam structure with honeycomb core filled of MRE (magnetorheological elastomer) with different ratios of Elastomer and iron particles is proposed. Modal response for structures with Nylon and Resin8000 honeycomb core filled with MRE and sandwiched between aluminum face sheets were analyzed and compared for two different ratios of MRE by placing magnets at free end and center of the structure. The force generated by magnets on the sandwich beam structure was calculated using ANSYS EDT and the modal response of the structure was then observed under generated magnetic force using ANSYS Workbench. The results showed that the resonance frequency of the structure decreased as the magnetic intensity was increased for all the cases specially for the first mode. Secondly structure with Nylon honeycomb core showed lower frequency drop and higher deformation than the structure with Resin8000 honeycomb core.
Vibration is experienced when a body is subjected to either internal or external forces which cause oscillation, with most operators of industrial equipment often exposed to high dosage, higher than the stipulated values. In this research, Digital Real-Time Frequency Analyzer (RSA 5106A) was used, while the results obtained were evaluated and compared with the health guidelines of the ISO 2631-1 : 1997 and ISO 2631-5 : 2004 standards, as described in the Health Guidance Caution Zone for a daily exposure action value (EAV) of 0.47 m/s2 and a daily exposure limit value (ELV) of 0.93 m/s. High acceleration was mostly seen on the z-axis in all the results obtained, whereas many were not within the HGCZ (Arms <0.47, and >0.93 m/s2). Comparing (VDV <8.5 m/s1.75 and >17 m/s1.75) with the ISO standard, the accelerations on all x- and y-axes were slightly within the HGCZ, with just a little below 0.47 m/s2 limit. The results obtained clearly showed that urgent action is needed virtually on all the equipment in both the Secondary Manufacturing Department (SMD) and Primary Manufacturing Department (PMD) to minimize vibration exposure on the technical operators.
Bone drilling is known as one of the most sensitive milling processes in biomedical engineering field. Fracture behavior of this cortical bone during drilling has attracted the attention of many researchers; however, there are still impending concerns such as necrosis, tool breakage, and microcracks due to high cutting forces, torques, and high vibration while drilling. This paper presents a comparative analysis of the cutting forces, torques, and vibration resulted on different bone samples (bovine, porcine, and artificial femur) using a 6dof Robot arm effector with considerations of its stiffness effects. Experiments were conducted on two spindle speeds of 1000 and 1500 rpm with a drill bit diameter of 2.5 mm and 6 mm depth of cut. The results obtained from the specimens were processed and analyzed using MATLAB R2015b and Visio 2000 software; these results were then compared with a prior test using manual and conventional drilling methods. The results obtained show that there is a significant drop in the average values of maximum drilling force for all the bone specimens when the spindle speed changes from 1000 rev/min to 1500 rev/min, with a drop from (20.07 to 12.34 N), approximately 23.85% for bovine, (11.25 to 8.14 N) with 16.03% for porcine, and (5.62 to 3.86 N) with 33.99% for artificial femur. The maximum average values of torque also decrease from 41.2 to 24.2 N·mm (bovine), 37.0 to 21.6 N·mm (porcine), and 13.6 to 6.7 N·mm (artificial femur), respectively. At an increase in the spindle speed, the vibration amplitude on all the bone samples also increases considerably. The variation in drilling force, torque, and vibration in our result also confirm that the stiffness of the robot effector joint has negative effect on the bone precision during drilling process.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.