Poly(l-lysine) grafted with poly(ethylene glycol) (PLL-g-PEG), a polycationic copolymer that is positively charged at neutral pH, spontaneously adsorbs from aqueous solution onto negatively charged surfaces, resulting in the formation of stable polymeric monolayers and rendering the surfaces protein-resistant to a degree related to the PEG surface density. A set of PLL-g-PEG polymers with different architectures was synthesized. The grafting ratio, g, of the polymer, defined as the ratio of the number of lysine monomers to the number of PEG side chains, was systematically varied between 2 and 23, and PEG molecular weights of 1, 2, and 5 kDa were used. The polymers were adsorbed onto niobium oxide-coated substrates, leading to highly different but well-controlled PEG surface densities with maximal values of 0.9, 0.5, and 0.3 chains/nm2 for the three PEG molecular weights, respectively. Time-of-flight secondary-ion mass spectrometry (ToF-SIMS) was used in conjunction with the in situ optical waveguide lightmode spectroscopy (OWLS) technique to investigate the interface architecture. While ToF-SIMS provided surface-analytical data on the polymeric adlayer, OWLS allowed the quantitative determination of the adsorbed polymer mass. Extremely good correlations were established between the ToF-SIMS data (obtained in UHV) and the in situ OWLS results. The amount of serum adsorbed, determined quantitatively by OWLS, was found to depend systematically on the surface coverage in terms of the ethylene glycol (EG) density, controlled by both PEG molecular weight and grafting ratio, g. Serum adsorption dropped gradually from 590 ng/cm2 on bare Nb2O5 to <2 ng/cm2 (=detection limit of the OWLS technique) for EG densities ≥ 20 nm-2. The PLL-g-PEG technology shows itself to be an efficient, cost-effective, and robust tool for the immobilization of PEG chains onto metal oxide surfaces. The precise control over PEG surface density across a wide range allows for the production of tailored surfaces with controlled degrees of bio-interactiveness. Such surfaces are expected to have a substantial potential for applications in biomedical and bioanalytical devices.

Poly(L-lysine)-g-poly(ethylene glycol) (PLL-g-PEG) copolymers with various grafting ratios were adsorbed to niobium pentoxide-coated silicon wafers and characterized before and after protein adsorption using X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Three proteins of different sizes, myoglobin (16 kD), albumin (67 kD), and fibrinogen (340 kD), were studied. XPS was used to quantify the amount of protein adsorbed to the bare and PEGylated surfaces. ToF-SIMS and principal component analysis (PCA) were used to study protein conformational changes on these surfaces. The smallest protein, myoglobin, generally adsorbed in higher numbers than the much larger fibrinogen. Protein adsorption was lowest on the surfaces with the highest PEG chain surface density and increased as the PEG layer density decreased. The highest adsorption was found on lysine-coated and bare niobium surfaces. ToF-SIMS and PCA data evaluation provided further information on the degree of protein denaturation, which, for a particular protein, were found to decrease with increasing PEG surface density and increase with decreasing protein size.

PEGylated Nb2O5 surfaces were obtained by the adsorption of poly(L-lysine)-g-poly(ethylene glycol) (PLL-g-PEG) copolymers, allowing control of the PEG surface density, as well as the surface charge. PEG (MW 2 kDa) surface densities between 0 and 0.5 nm(-2) were obtained by changing the PEG to lysine-mer ratio in the PLL-g-PEG polymer, resulting in net positive, negative and neutral surfaces. Colloid probe atomic force microscopy (AFM) was used to characterize the interfacial forces associated with the different surfaces. The AFM force analysis revealed interplay between electrical double layer and steric interactions, thus providing information on the surface charge and on the PEG layer thickness as a function of copolymer architecture. Adsorption of the model proteins lysozyme, alpha-lactalbumin, and myoglobin onto the various PEGylated surfaces was performed to investigate the effect of protein charge. In addition, adsorption experiments were performed over a range of ionic strengths, to study the role of electrostatic forces between surface charges and proteins acting through the PEG layer. The adsorbed mass of protein, measured by optical waveguide lightmode spectroscopy (OWLS), was shown to depend on a combination of surface charge, protein charge, PEG thickness, and grafting density. At high grafting density and high ionic strength, the steric barrier properties of PEG determine the net interfacial force. At low ionic strength, however, the electrical double layer thickness exceeds the thickness of the PEG layer, and surface charges "shining through" the PEG layer contribute to protein interactions with PLL-g-PEG coated surfaces. The combination of AFM surface force measurements and protein adsorption experiments provides insights into the interfacial forces associated with various PEGylated surfaces and the mechanisms of protein resistance.