International audienceIn ophiolites and in present-day oceanic crust formed at fast spreading ridges, oceanic plagiogranites are commonly observed at, or close to the base of the sheeted dike complex. They can be produced either by differentiation of mafic melts, or by hydrous partial melting of the hydrothermally altered sheeted dikes. In addition, the hydrothermally altered base of the sheeted dike complex, which is often infiltrated by plagiogranitic veins, is usually recrystallized into granoblastic dikes that are commonly interpreted as a result of prograde granulitic metamorphism. To test the anatectic origin of oceanic plagiogranites, we performed melting experiments on a natural hydrothermally altered dike, under conditions that match those prevailing at the base of the sheeted dike complex. All generated melts are water saturated, transitional between tholeiitic and calc-alkaline, and match the compositions of oceanic plagiogranites observed close to the base of the sheeted dike complex. Newly crystallized clinopyroxene and plagioclase have compositions that are characteristic of the same minerals in granoblastic dikes. Published silicic melt compositions obtained in classical MORB fractionation experiments also broadly match the compositions of oceanic plagiogranites; however, the compositions of the coexisting experimental minerals significantly deviate from those of the granoblastic dikes. Our results demonstrate that hydrous partial melting is a likely common process in the root zone of the sheeted dike complex, starting at temperatures exceeding 850A degrees C. The newly formed melt can either crystallize to form oceanic plagiogranites or may be recycled within the melt lens resulting in hybridized and contaminated MORB melts. It represents the main MORB crustal contamination process. The residue after the partial melting event is represented by the granoblastic dikes. Our results support a model with a dynamic melt lens that has the potential to trigger hydrous partial melting reactions in the previously hydrothermally altered sheeted dikes. A new thermometer using the Al content of clinopyroxene is also elaborated

No abstract

The aim of the Iceland Deep Drilling Project is to drill into supercritical geothermal systems and examine their economic potential. The exploratory well IDDP-2 was drilled in the Reykjanes geothermal field in SW Iceland, on the landward extension of the Mid-Atlantic Ridge. The Reykjanes geothermal field produces from a b300°C reservoir at 1 to 2.5 km depth and is unusual because it is recharged by seawater. The well was cased to 3000 m depth, and then angled towards the main up-flow zone of the system, to a total slant depth of 4659 m (~4500 m vertical depth). Based on alteration mineral assemblages, joint inversion of wireline logging, and rate of heating measurements, the bottom hole temperature is estimated to be about 535°C. The major problem encountered during drilling was the total loss of circulation below 3 km depth and continuing to the final depth. Drilling continued without recovering drill cuttings, consequently spot coring provided the only deep rock samples from the well. These cores are characteristic of a basaltic sheeted dike complex, with hydrothermal alteration mineral assemblages that range from greenschist to amphibolite facies, hornblende hornfels, and pyroxene hornfels, allowing the opportunity to investigate water-rock interaction in the active roots of an analog of a submarine hydrothermal system. As they have not yet been sampled, the composition of the deep fluids at Reykjanes is unknown at present. Cold water is currently being injected with the aim of enhancing permeability at depth, before allowing the well to heat up prior to flow tests planned for early 2019. The well has at least two fluid feed zones, a dominant one at 3.4 km depth and a second smaller one at 4.5 km. Extensive geophysical surveys of the Reykjanes Peninsula completed recently allow correlation of geophysical signals with rocks properties and in-situ conditions in the subsurface. Earthquake activity monitored with a local seismic network during drilling the IDDP-2 drilling detected abundant small earthquakes (M L ≤ 2) within the depth range of 3-5 km. A zone at 3-5 km depth below the producing geothermal field that was generally aseismic prior to drilling, but became seismically active during the drilling. The drilling of the IDDP-2 has achieved number of scientific and engineering firsts. It is the deepest and hottest drill hole so far sited on an active mid-ocean spreading center. It penetrated an active supercritical hydrothermal environment at depths analogous to those postulated as the high temperature reaction zones feeding black smoker systems.