No abstract

To examine the utilization of metal oxide nanoparticles (NPs) in different commercial products, this work focuses on the determination of cost-effective and scalable synthesis protocols. The solvothermal protocol is well-known as a scalable method but has recently been shown to lack economic feasibility. The mechanochemical method has recently been recognized to be a more economic and environmentally friendly substitute for the solvothermal method. In this study, zinc oxide nanoparticles (ZnO NPs) and copper oxide nanoparticles (CuO NPs) were synthesized using two (aqueous and organic) solvothermal (wet) methods and two (manual and automated) mechanochemical (dry) methods. The four methods were evaluated and compared. The automated mechanochemical method generated a significantly higher yield of ZnO NPs (82%) and CuO NPs (84%) using the least energy and time. However, the prepared ZnO NPs displayed higher cytotoxicity against Vero E6 cells when compared to that of CuO NPs. Because of their low cytotoxicity, CuO NPs synthesized via the automated mechanochemical method were selected for application onto cotton fabrics. Lower cytotoxicity was observed for CuO NPs treated fabrics with an IC 50 of 562 mg/mL and ZnO treated fabrics with an IC 50 at 23.93 mg/mL when the treated fabrics were tested against L929 fibroblast cells. Additionally, the cotton fabrics retained bactericidal and virucidal effects after four washes. Thus, the current study recommends the automated mechanochemical method as a cost-effective scalable approach for the synthesis of CuO NPs. The application of CuO NPs onto cotton fabrics generated washable antimicrobial face masks.

Developing effective stem cell based therapies requires the design of complex in vitro culture systems for more accurate representation of the stem cell niche. Attempts to improve conventional cell culture platforms include the use of biomaterial coated culture plates, sphere culture, microfluidic systems and bioreactors. Most of these platforms are not cost-effective, require industrial technical expertise to fabricate, and remain too simplistic compared to the physiological cell niche. The human amniotic membrane (hAM) has been used successfully in clinical grafting applications due to its unique biological composition and regenerative properties. In this study, we present a combinatorial platform that integrates the hAM with biomolecular, topographic and mechanical cues in one versatile model.MethodsWe utilized the hAM to provide the biological and the three dimensional (3D) topographic components of the prototype. The 3D nano-roughness of the hAM was characterized using surface electron microscopy and surface image analysis (ImageJ and SurfaceJ). We developed additional macro-scale and micro-scale versions of the platform which provided additional shear stress factors to simulate the fluid dynamics of the in vivo extracellular fluids.ResultsThree models of varying complexities of the prototype were assembled. A well-defined 3D surface modulation of the hAM in comparable to commercial 3D biomaterial culture substrates was achieved without complex fabrication and with significantly lower cost. Performance of the prototype was demonstrated through culture of primary human umbilical cord mononuclear blood cells (MNCs), human bone marrow mesenchymal stem cell line (hBMSC), and human breast cancer tissue.ConclusionThis study presents methods of assembling an integrated, flexible and low cost biomimetic cell culture platform for diverse cell culture applications.

Over the past several decades, the development of engineered small particles as targeted and drug delivery systems (TDDS) has received great attention thanks to the possibility to overcome the limitations of classical cancer chemotherapy, including targeting incapability, nonspecific action and, consequently, systemic toxicity. Thus, this research aims at using a novel design of Poly(N-isopropylacrylamide) p(NIPAM)-based microgels to specifically target cancer cells and avoid the healthy ones, which is expected to decrease or eliminate the side effects of chemotherapeutic drugs. Smart NIPAM-based microgels were functionalized with acrylic acid and coupled to folic acid (FA), targeting the folate receptors overexpressed by cancer cells and to the chemotherapeutic drug doxorubicin (Dox). The successful conjugation of FA and Dox was demonstrated by dynamic light scattering (DLS), Fourier-transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), UV-VIS analysis, and differential scanning calorimetry (DSC). Furthermore, viability assay performed on cancer and healthy breast cells, suggested the microgels’ biocompatibility and the cytotoxic effect of the conjugated drug. On the other hand, the specific tumor targeting of synthetized microgels was demonstrated by a co-cultured (healthy and cancer cells) assay monitored using confocal microscopy and flow cytometry. Results suggest successful targeting of cancer cells and drug release. These data support the use of pNIPAM-based microgels as good candidates as TDDS.

The present study describes the development of multifunctional hemostatic sponges to control bleeding. Chitosan (Ch) and poly(vinyl alcohol) (PVA) were selected as the basic polymeric matrix [Ch/PVA] for sponges. Glycerol and citric acid were used as crosslinkers [Ch/PVA/G(Cl)] to enhance the mechanical properties of the developed sponges. Ciprofloxacin (AB) was added to the developed sponge to impart antibacterial activity. Hydroxyapatite (HA) was also added, which would make the sponge suitable for bone surgery. Among the developed sponges, the Ch/PVA/G(Cl)-HA-AB sponge demonstrated enhanced cell viability, mechanical properties, and strong antimicrobial effect against Escherichia coli , Pseudomonas aeruginosa , and Staphylococcus aureus , in addition to platelet aggregation activity. The addition of ciprofloxacin and hydroxyapatite promotes a unique synergistic effect of antimicrobial activity and hemostasis. Thus, the present study introduces Ch/PVA/G(Cl)-HA-AB, a multifunctional hemostatic sponge that would be suitable for bone surgical applications.