The improvement of the thermal insulating material thermophysical characteristics of the thermal protection elements by studying the porous structure is a promising direction of research. The article describes the effects of the porosity and coupling of the porous structure on the thermophysical characteristics of thermal insulating materials. The article uses standard systematized techniques and instruments of scientific research applied in thermophysics. The research methodology of highly-porous material thermophysical properties is based on performance of empirical laboratory investigations of the samples obtained. It was found that for the pore structure effect on the material characteristics it is rational to use the following complex indices: porosity, number of pores, pore position in space, the pore form, pore formation energy. The article shows the effect of the porous structure on the thermophysical characteristics of the material. The complex parameters of the porous structure, which will allow to develop a new method of control of the porous structure, are proposed. As a result of the experiment planning method, the regression equation of an effective coefficient of thermal conductivity for porous thermal protection structures was developed. It was established that for a more even distribution of the mixture in a volume it is necessary to minimize the size of the dispersed components, thereby increasing the area of their contacts. The experimental method revealed that the moisture evaporation caused the formation of pores inside the clay. The shape of the pores was determined using electron microscope MMP-2P, both on the sample section and surface. The clearest clay has the greatest porosity (no iron oxide and calcium oxide). The pores have a spherical shape in it. The presence of impurities reduces the material porosity due to the increased clay viscosity.
Гомогенизация отливок из литых алюминиевых сплавов имеет приоритетное значение для улучшения их технологических параметров. Режим гомогенизирующего отжига регулируется двумя параметрами-температурой и временем выдержки. Традиционно используются одно или двухступенчатые режимы отжига. Для оценки степени гомогенности расплава после таких термообработок на предприятиях, как правило, используются различные методы механических испытаний. В работе предлагается новый метод расчета критерия оценки гомогенности структуры литых сплавов на примере алюминиевого сплава В95. Критерием гомогенности γ может служить степень приближения составов локальных объемов литых сплавов к марочному составу. Как показывает опыт, измерения содержания легирующих элементов удобнее проводить по осям дендритов. Дендриты, как правило, обеднены основными легирующими элементами, которые обычно локализованы в междендритных объемах. Принимая за величину, характеризующую степень негомогенности литого сплава, отклонение состава от марочного (Δ), критерий гомогенности можно представить в виде: γ i = 1-Δ. Для совершенного гомогенного сплава значение критерия гомогенности должно приближаться к 1. Рассчитанный по данной формуле средний коэффициент гомогенности для литого сплава В95 равен γ ∑ = 0,503. Сравнивая содержание легирующих элементов в центре зерен и по границам гомогенизированных зерен, следует отметить, что локальный состав зерен и в центре, и на границах стал близок к марочному составу сплава В95. На это указывает и близкий к 1 введенный ранее условный коэффициент гомогенности γ. Действительно, средний коэффициент гомогенности стал равен γ ∑ = 0,94. Предложенный метод рекомендован в качестве аналитического способа для оценки степени гомогенности алюминиевых литых сплавов, а в качестве критерия гомогенности γ можно предложить обобщенный расчетный показатель, построенный на основе анализа локальных составов по осям дендритов и междендритных областей.
The paper describes analysis of the structure and the complex of magnetic properties of 251510 mm sized magnetic circuits weighing 18-22 g made of Fe or Co based amorphous alloy ribbon 20-30 m in thickness. It is been demonstrated that the crystallization process during continuous heating of all amorphous alloys proceeds in two stages in near temperature ranges of 500-600 and 650-750 °С. Crystallization at the beginning of the first range, when the formed amorphous-nanocrystalline state forms, results in additional improvement of magnetic properties of all alloys. The higher complex of magnetic properties (very low coercive force H c < 1.0 A/m, high values of saturation induction B M = 0.67 T and permeability μ max > 10 5 , low degree of hysteresis loop squareness B r /B max = 0.4-0.5) is formed in magnetic circuits from a Finemet type alloy after annealing at 500-560 °С when the dimensions of emerging nanocrystals make 14-15 nm. An increase of temperature above the optimal range for each alloy causes intensive development of crystallization, leads to increase in size of the formed crystallites and worsens the complex of magnetic properties. Annealing of magnetic circuits from a Finemet type alloy at temperatures of 590-600 °С, where the first range of crystallization ends, has little effect on the degree of crystallization, but leads to an increase of crystallite size resulting in a decrease of saturation induction and an increase of coercive force.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.